<?xml version="1.0" encoding="UTF-8"?><rss version="2.0"
	xmlns:content="http://purl.org/rss/1.0/modules/content/"
	xmlns:wfw="http://wellformedweb.org/CommentAPI/"
	xmlns:dc="http://purl.org/dc/elements/1.1/"
	xmlns:atom="http://www.w3.org/2005/Atom"
	xmlns:sy="http://purl.org/rss/1.0/modules/syndication/"
	xmlns:slash="http://purl.org/rss/1.0/modules/slash/"
	>

<channel>
	<title>Passive Components | Sensors &amp; Electronic Components - DuoMy</title>
	<atom:link href="https://www.duomy.com/product-category/passive-components/feed/" rel="self" type="application/rss+xml" />
	<link>https://www.duomy.com/product-category/passive-components/</link>
	<description></description>
	<lastBuildDate>Fri, 20 Nov 2026 01:17:52 +0000</lastBuildDate>
	<language>en-US</language>
	<sy:updatePeriod>
	hourly	</sy:updatePeriod>
	<sy:updateFrequency>
	1	</sy:updateFrequency>
	<generator>https://wordpress.org/?v=7.1.5</generator>

<image>
	<url>https://www.duomy.com/wp-content/uploads/2026/04/cropped-电子-32x32.png</url>
	<title>Passive Components | Sensors &amp; Electronic Components - DuoMy</title>
	<link>https://www.duomy.com/product-category/passive-components/</link>
	<width>32</width>
	<height>32</height>
</image> 
	<item>
		<title>10 kΩ Glass-Encapsulated NTC, B = 3950, Axial Leads</title>
		<link>https://www.duomy.com/products/10k-ntc-glass-axial-3950/</link>
		
		<dc:creator><![CDATA[]]></dc:creator>
		<pubDate>Fri, 20 Nov 2026 01:17:52 +0000</pubDate>
				<guid isPermaLink="false">https://www.duomy.com/products/10k-ntc-glass-axial-3950/</guid>

					<description><![CDATA[<p>Glass-encapsulated axial NTC thermistor, 10 kΩ at 25 °C, B = 3950 K, ±1%, rated to +250 °C. For probes, hot air ducts and any position where an SMD part would desolder.</p>
<p>The post <a href="https://www.duomy.com/products/10k-ntc-glass-axial-3950/">10 kΩ Glass-Encapsulated NTC, B = 3950, Axial Leads</a> appeared first on <a href="https://www.duomy.com">DuoMy Sensing</a>.</p>
]]></description>
										<content:encoded><![CDATA[<h2>Overview</h2>
<p>The glass bead is what makes a thermistor usable above the melting point of solder. Encapsulated in glass with axial leads, the element can sit in a hot air duct, against a heating element or inside a probe tube at 250 °C, positions where an SMD part would simply fall off the board.</p>
<p>The thin leads also decouple the sensor from the board thermally. In a probe assembly, the bead measures the medium and the leads carry only the signal, which is why the same element appears in both board-mount and probe products.</p>
<h2>Key features</h2>
<ul>
<li>Rated to +250 °C</li>
<li>Glass encapsulation, chemically inert</li>
<li>25 mm axial leads for remote placement</li>
<li>3 s thermal time constant, faster than an SMD part</li>
<li>Insulation resistance above 100 MΩ</li>
</ul>
<h2>Typical applications</h2>
<ul>
<li>Temperature probes and probe assemblies</li>
<li>Hot air ducts and heater control</li>
<li>Oven and cooking appliance sensing</li>
<li>Industrial process temperature measurement</li>
</ul>
<h2>Selection note</h2>
<p>The glass bead is fragile. Support the leads close to the body when bending them, and do not clamp the bead itself in a metal holder.</p>
<h2>Ordering</h2>
<p>Send the temperature range, the medium and the probe or mounting arrangement. We confirm the lead length and insulation, then quote.</p>
<p>The post <a href="https://www.duomy.com/products/10k-ntc-glass-axial-3950/">10 kΩ Glass-Encapsulated NTC, B = 3950, Axial Leads</a> appeared first on <a href="https://www.duomy.com">DuoMy Sensing</a>.</p>
]]></content:encoded>
					
		
		
			</item>
		<item>
		<title>Power NTC Inrush Limiter, 5 Ω 3 A, 10 mm Disc</title>
		<link>https://www.duomy.com/products/power-ntc-inrush-limiter-5r-3a/</link>
		
		<dc:creator><![CDATA[]]></dc:creator>
		<pubDate>Fri, 20 Nov 2026 01:17:52 +0000</pubDate>
				<guid isPermaLink="false">https://www.duomy.com/products/power-ntc-inrush-limiter-5r-3a/</guid>

					<description><![CDATA[<p>Power NTC thermistor for inrush current limiting, 5 Ω at 25 °C, 3 A steady current, 10 mm disc. Limits the surge into a capacitor bank at power-up, then self-heats out of the circuit.</p>
<p>The post <a href="https://www.duomy.com/products/power-ntc-inrush-limiter-5r-3a/">Power NTC Inrush Limiter, 5 Ω 3 A, 10 mm Disc</a> appeared first on <a href="https://www.duomy.com">DuoMy Sensing</a>.</p>
]]></description>
										<content:encoded><![CDATA[<h2>Overview</h2>
<p>At power-up, an empty capacitor bank looks like a short circuit and the inrush is limited only by the wiring. A power NTC in series with the input starts at 5 Ω, which caps that surge, and then heats up as the operating current flows through it until the resistance falls to a fraction of an ohm.</p>
<p>The catch is that it only works from cold. Switch the equipment off and on again within a few seconds and the thermistor is still hot, so the second inrush is nearly unlimited. Where rapid cycling is expected, a relay or a triac that bypasses the thermistor after start-up is required.</p>
<h2>Key features</h2>
<ul>
<li>5 Ω cold resistance limiting inrush current</li>
<li>Falls to 0.35 Ω at 3 A steady current</li>
<li>50 J energy absorption for a capacitor bank</li>
<li>10 mm disc, 7.5 mm lead pitch</li>
<li>Self-heating operation, no control circuit</li>
</ul>
<h2>Typical applications</h2>
<ul>
<li>Inrush limiting ahead of a switching supply</li>
<li>Motor soft-start on small drives</li>
<li>Battery charger input protection</li>
<li>Equipment with a large input capacitor bank</li>
</ul>
<h2>Selection note</h2>
<p>There is no protection on a hot restart. If the equipment can be switched off and on within seconds, add a bypass relay or a fixed resistor with a relay, not a bigger thermistor.</p>
<h2>Ordering</h2>
<p>Send the input voltage, capacitor bank size, steady current and restart pattern. We confirm the disc size and energy rating, then quote.</p>
<p>The post <a href="https://www.duomy.com/products/power-ntc-inrush-limiter-5r-3a/">Power NTC Inrush Limiter, 5 Ω 3 A, 10 mm Disc</a> appeared first on <a href="https://www.duomy.com">DuoMy Sensing</a>.</p>
]]></content:encoded>
					
		
		
			</item>
		<item>
		<title>10 kΩ NTC Thermistor, B = 3435, 0805, ±1%</title>
		<link>https://www.duomy.com/products/10k-ntc-b3435-0805/</link>
		
		<dc:creator><![CDATA[]]></dc:creator>
		<pubDate>Fri, 20 Nov 2026 01:17:51 +0000</pubDate>
				<guid isPermaLink="false">https://www.duomy.com/products/10k-ntc-b3435-0805/</guid>

					<description><![CDATA[<p>Surface-mount NTC thermistor, 10 kΩ at 25 °C, B25/85 = 3435 K, ±1%, 0805 body. Flatter curve than a 3950 K part, for circuits that measure over a wide range.</p>
<p>The post <a href="https://www.duomy.com/products/10k-ntc-b3435-0805/">10 kΩ NTC Thermistor, B = 3435, 0805, ±1%</a> appeared first on <a href="https://www.duomy.com">DuoMy Sensing</a>.</p>
]]></description>
										<content:encoded><![CDATA[<h2>Overview</h2>
<p>The B value sets how steeply the resistance changes with temperature. A 3435 K part changes more gently than a 3950 K part, which matters when the measurement range is wide: over 0 to 100 °C a steeper curve gives better resolution at the low end and worse at the high end, and the flatter part spreads the resolution more evenly.</p>
<p>Both are 10 kΩ at 25 °C, so they are interchangeable in a divider only if the firmware uses the matching B value. Substituting one for the other without changing the table gives a reading that is correct at room temperature and wrong everywhere else.</p>
<h2>Key features</h2>
<ul>
<li>10 kΩ at 25 °C, B25/85 = 3435 K</li>
<li>Flatter resistance curve over a wide range</li>
<li>0805 body, 200 mW dissipation</li>
<li>±1% tolerance on resistance and B value</li>
<li>Same footprint family as the 3950 K part</li>
</ul>
<h2>Typical applications</h2>
<ul>
<li>Wide-range temperature measurement</li>
<li>HVAC return and supply air sensing</li>
<li>Appliance temperature control</li>
<li>Battery pack monitoring</li>
</ul>
<h2>Selection note</h2>
<p>The B value is part of the firmware table. Replacing a 3435 K part with a 3950 K part without updating the table produces a reading that is right at 25 °C and wrong at both ends.</p>
<h2>Ordering</h2>
<p>Send the resistance, B value and the temperature range you need to resolve. We confirm the curve and the divider, then quote.</p>
<p>The post <a href="https://www.duomy.com/products/10k-ntc-b3435-0805/">10 kΩ NTC Thermistor, B = 3435, 0805, ±1%</a> appeared first on <a href="https://www.duomy.com">DuoMy Sensing</a>.</p>
]]></content:encoded>
					
		
		
			</item>
		<item>
		<title>10 kΩ NTC Thermistor, B = 3950, 0603, ±1%</title>
		<link>https://www.duomy.com/products/10k-ntc-b3950-0603/</link>
		
		<dc:creator><![CDATA[]]></dc:creator>
		<pubDate>Fri, 20 Nov 2026 01:17:50 +0000</pubDate>
				<guid isPermaLink="false">https://www.duomy.com/products/10k-ntc-b3950-0603/</guid>

					<description><![CDATA[<p>Surface-mount NTC thermistor, 10 kΩ at 25 °C, B25/85 = 3950 K, ±1% resistance tolerance, 0603 body. Board-level temperature sensing for compensation and protection.</p>
<p>The post <a href="https://www.duomy.com/products/10k-ntc-b3950-0603/">10 kΩ NTC Thermistor, B = 3950, 0603, ±1%</a> appeared first on <a href="https://www.duomy.com">DuoMy Sensing</a>.</p>
]]></description>
										<content:encoded><![CDATA[<h2>Overview</h2>
<p>An NTC thermistor is a resistor whose value falls as temperature rises, and 10 kΩ with a 3950 K B value is the combination that most temperature-sensing circuits are designed around. A 1% tolerance on resistance and B value is what makes the reading usable without calibrating every board.</p>
<p>The measurement is only as good as the thermal contact. Mounted on a board, the thermistor reports the board temperature, which lags the air and is warmer than the air near a regulator. For air temperature, a leaded part or a slot in the PCB is required.</p>
<h2>Key features</h2>
<ul>
<li>10 kΩ at 25 °C, B25/85 = 3950 K</li>
<li>±1% resistance and B value tolerance</li>
<li>0603 body for placement at the measurement point</li>
<li>100 mW maximum dissipation</li>
<li>5 s thermal time constant in still air</li>
</ul>
<h2>Typical applications</h2>
<ul>
<li>Board temperature monitoring</li>
<li>Temperature compensation of analogue circuits</li>
<li>Battery and power stage thermal protection</li>
<li>Fan control and thermal throttling</li>
</ul>
<h2>Selection note</h2>
<p>A thermistor measuring board temperature will not give the air temperature. If the reading is used for a control loop on ambient, move the sensor away from heat sources or use a leaded part.</p>
<h2>Ordering</h2>
<p>Send the resistance at 25 °C, the B value and the tolerance. We confirm the curve against your divider, then quote.</p>
<p>The post <a href="https://www.duomy.com/products/10k-ntc-b3950-0603/">10 kΩ NTC Thermistor, B = 3950, 0603, ±1%</a> appeared first on <a href="https://www.duomy.com">DuoMy Sensing</a>.</p>
]]></content:encoded>
					
		
		
			</item>
		<item>
		<title>ESD Protection Array, 5 V, 2-Line, SOT-23</title>
		<link>https://www.duomy.com/products/tvs-array-sot23-5v-esd/</link>
		
		<dc:creator><![CDATA[]]></dc:creator>
		<pubDate>Fri, 20 Nov 2026 01:17:28 +0000</pubDate>
				<guid isPermaLink="false">https://www.duomy.com/products/tvs-array-sot23-5v-esd/</guid>

					<description><![CDATA[<p>Two-line bidirectional ESD protection array, 5 V standoff, 12 pF line capacitance, SOT-23. Clamping for USB, HDMI and other high-speed interfaces without distorting the signal.</p>
<p>The post <a href="https://www.duomy.com/products/tvs-array-sot23-5v-esd/">ESD Protection Array, 5 V, 2-Line, SOT-23</a> appeared first on <a href="https://www.duomy.com">DuoMy Sensing</a>.</p>
]]></description>
										<content:encoded><![CDATA[<h2>Overview</h2>
<p>An ESD array is a TVS optimised for one job: absorb a human-body discharge at a connector without adding enough capacitance to ruin the signal. Twelve picofarads keeps a USB 2.0 or full-speed differential pair intact, while a general-purpose 500 pF TVS would round off the edges and destroy the eye diagram.</p>
<p>The clamping voltage of 9.8 V at 1 A is what protects the transceiver behind it. The interface IC sees a short excursion to under 10 V instead of the kilovolt that arrived at the connector, which is within what its own internal diodes can survive.</p>
<h2>Key features</h2>
<ul>
<li>Two bidirectional lines in one SOT-23</li>
<li>12 pF line capacitance for high-speed data</li>
<li>±15 kV contact discharge rating</li>
<li>Clamping at 9.8 V, compatible with 5 V logic</li>
<li>Low leakage, 0.1 µA at 5 V</li>
</ul>
<h2>Typical applications</h2>
<ul>
<li>USB 2.0 and Type-C data line protection</li>
<li>HDMI and display interface protection</li>
<li>Keypad and button lines at an enclosure entry</li>
<li>External connector protection on portable equipment</li>
</ul>
<h2>Selection note</h2>
<p>Keep the protected trace and the ground return parallel and short. The clamp only works if the discharge current can return to the connector without crossing the circuit it is protecting.</p>
<h2>Ordering</h2>
<p>Send the interface type, data rate and line voltage. We confirm the capacitance and clamping level, then quote.</p>
<p>The post <a href="https://www.duomy.com/products/tvs-array-sot23-5v-esd/">ESD Protection Array, 5 V, 2-Line, SOT-23</a> appeared first on <a href="https://www.duomy.com">DuoMy Sensing</a>.</p>
]]></content:encoded>
					
		
		
			</item>
		<item>
		<title>TVS Diode, 33 V Standoff, 400 W, SMB</title>
		<link>https://www.duomy.com/products/tvs-diode-smb-33v-400w/</link>
		
		<dc:creator><![CDATA[]]></dc:creator>
		<pubDate>Fri, 20 Nov 2026 01:17:27 +0000</pubDate>
				<guid isPermaLink="false">https://www.duomy.com/products/tvs-diode-smb-33v-400w/</guid>

					<description><![CDATA[<p>Unidirectional transient voltage suppressor, 33 V standoff, 400 W peak pulse power, 53.3 V clamping, SMB package. Board-level protection for 24 V rails and inductive loads.</p>
<p>The post <a href="https://www.duomy.com/products/tvs-diode-smb-33v-400w/">TVS Diode, 33 V Standoff, 400 W, SMB</a> appeared first on <a href="https://www.duomy.com">DuoMy Sensing</a>.</p>
]]></description>
										<content:encoded><![CDATA[<h2>Overview</h2>
<p>A TVS diode clamps in nanoseconds, which is the timescale that matters for an ESD event or an inductive kick. The varistor handles bulk energy at the mains input; the TVS handles the fast edge on a board, and the two work at different levels of the same protection scheme.</p>
<p>The standoff voltage has to be above the highest normal voltage on the node, including tolerance and ripple. Thirty-three volts is right for a 24 V rail with margin; a 24 V TVS on that rail would leak and eventually fail, because it would be conducting on normal operation.</p>
<h2>Key features</h2>
<ul>
<li>33 V standoff, 36.7 V minimum breakdown</li>
<li>400 W peak pulse power at 10/1000 µs</li>
<li>Clamping at 53.3 V, below the tolerance of most 24 V circuitry</li>
<li>SMB package for surface-mount assembly</li>
<li>Nanosecond response time</li>
</ul>
<h2>Typical applications</h2>
<ul>
<li>24 V rail transient protection</li>
<li>Relay and solenoid inductive kick clamping</li>
<li>Automotive load dump suppression (secondary)</li>
<li>Industrial I/O protection</li>
</ul>
<h2>Selection note</h2>
<p>Place the TVS as close to the connector as possible and return it to a solid ground with a short, wide trace. A TVS two centimetres from the entry protects the trace, not the circuit.</p>
<h2>Ordering</h2>
<p>Send the rail voltage, the transient level and the package preference. We confirm the standoff and clamping voltage, then quote.</p>
<p>The post <a href="https://www.duomy.com/products/tvs-diode-smb-33v-400w/">TVS Diode, 33 V Standoff, 400 W, SMB</a> appeared first on <a href="https://www.duomy.com">DuoMy Sensing</a>.</p>
]]></content:encoded>
					
		
		
			</item>
		<item>
		<title>14 mm Metal-Oxide Varistor, 275 V AC</title>
		<link>https://www.duomy.com/products/14mm-mov-275vac/</link>
		
		<dc:creator><![CDATA[]]></dc:creator>
		<pubDate>Fri, 20 Nov 2026 01:17:26 +0000</pubDate>
				<guid isPermaLink="false">https://www.duomy.com/products/14mm-mov-275vac/</guid>

					<description><![CDATA[<p>Metal-oxide varistor, 14 mm disc, 275 V AC continuous, 430 V at 1 mA, 100 J energy absorption. Line-to-line surge clamping at the input of industrial equipment.</p>
<p>The post <a href="https://www.duomy.com/products/14mm-mov-275vac/">14 mm Metal-Oxide Varistor, 275 V AC</a> appeared first on <a href="https://www.duomy.com">DuoMy Sensing</a>.</p>
]]></description>
										<content:encoded><![CDATA[<h2>Overview</h2>
<p>A varistor is a voltage-dependent resistor: high resistance at the operating voltage, low resistance above its threshold, so a surge is diverted into the device instead of into the circuit behind it. The 430 V threshold on a 275 V AC line leaves headroom for normal mains variation and clamps before the insulation of the equipment is stressed.</p>
<p>Every surge event consumes part of the device. The 100 J rating is the total energy it can absorb before the disc degrades, and a varistor that has taken repeated hits drifts to a lower threshold and eventually fails short. That is why a failed varistor is usually found as a short circuit at the input, not as an open.</p>
<h2>Key features</h2>
<ul>
<li>275 V AC continuous rating for 230 V mains</li>
<li>100 J energy absorption, 4,500 A peak current</li>
<li>430 V threshold with ±10% tolerance</li>
<li>14 mm disc, 7.5 mm lead pitch</li>
<li>Fails short, which is detectable at the input</li>
</ul>
<h2>Typical applications</h2>
<ul>
<li>AC input surge protection</li>
<li>Protection ahead of a switching supply</li>
<li>Industrial equipment on exposed mains</li>
<li>Motor drive input transient clamping</li>
</ul>
<h2>Selection note</h2>
<p>A varistor needs a fuse or a breaker ahead of it. When it fails short, that fuse is what removes the fault current; without it, the varistor becomes the fault.</p>
<h2>Ordering</h2>
<p>Send the mains voltage, expected surge level and the fuse rating upstream. We confirm the disc size and energy rating, then quote.</p>
<p>The post <a href="https://www.duomy.com/products/14mm-mov-275vac/">14 mm Metal-Oxide Varistor, 275 V AC</a> appeared first on <a href="https://www.duomy.com">DuoMy Sensing</a>.</p>
]]></content:encoded>
					
		
		
			</item>
		<item>
		<title>7 mm Metal-Oxide Varistor, 130 V AC</title>
		<link>https://www.duomy.com/products/07mm-mov-130vac/</link>
		
		<dc:creator><![CDATA[]]></dc:creator>
		<pubDate>Fri, 20 Nov 2026 01:17:26 +0000</pubDate>
				<guid isPermaLink="false">https://www.duomy.com/products/07mm-mov-130vac/</guid>

					<description><![CDATA[<p>Metal-oxide varistor, 7 mm disc, 130 V AC continuous, 200 V at 1 mA, 20 J energy absorption. Compact surge clamping for 120 V mains and low-power boards.</p>
<p>The post <a href="https://www.duomy.com/products/07mm-mov-130vac/">7 mm Metal-Oxide Varistor, 130 V AC</a> appeared first on <a href="https://www.duomy.com">DuoMy Sensing</a>.</p>
]]></description>
										<content:encoded><![CDATA[<h2>Overview</h2>
<p>The 7 mm disc is the small-board version: 20 J of absorption and 1,200 A peak current, enough for the surge that arrives on a 120 V supply through a short cable, in a package that fits beside a terminal block. It is a compromise between protection level and board area, and the board area is usually the constraint.</p>
<p>For a location with a long outdoor cable or a known lightning exposure, the 14 mm or 20 mm disc carries more energy and should be used instead. The 7 mm part is for equipment inside a building on a normal branch circuit.</p>
<h2>Key features</h2>
<ul>
<li>130 V AC rating for 120 V mains</li>
<li>7 mm disc, 5 mm lead pitch</li>
<li>20 J energy absorption, 1,200 A peak</li>
<li>Compact footprint beside terminal blocks</li>
<li>Fail-short behaviour detectable at the input</li>
</ul>
<h2>Typical applications</h2>
<ul>
<li>120 V equipment input protection</li>
<li>Power boards with limited space</li>
<li>Secondary surge clamping after a larger device</li>
<li>Appliance control boards</li>
</ul>
<h2>Selection note</h2>
<p>A 7 mm varistor is not a lightning arrester. On an exposed line, use a larger disc and coordinate it with the upstream protection rather than relying on the small part alone.</p>
<h2>Ordering</h2>
<p>Send the mains voltage, exposure level and available board area. We size the disc for the energy, then quote.</p>
<p>The post <a href="https://www.duomy.com/products/07mm-mov-130vac/">7 mm Metal-Oxide Varistor, 130 V AC</a> appeared first on <a href="https://www.duomy.com">DuoMy Sensing</a>.</p>
]]></content:encoded>
					
		
		
			</item>
		<item>
		<title>16 MHz Ceramic Resonator, 3-Pin with Built-In Capacitors</title>
		<link>https://www.duomy.com/products/16mhz-ceramic-resonator-3pin/</link>
		
		<dc:creator><![CDATA[]]></dc:creator>
		<pubDate>Fri, 20 Nov 2026 01:17:25 +0000</pubDate>
				<guid isPermaLink="false">https://www.duomy.com/products/16mhz-ceramic-resonator-3pin/</guid>

					<description><![CDATA[<p>Three-pin ceramic resonator, 16 MHz ±0.5%, with built-in load capacitors. A clock reference that needs no external capacitors and starts reliably at low cost.</p>
<p>The post <a href="https://www.duomy.com/products/16mhz-ceramic-resonator-3pin/">16 MHz Ceramic Resonator, 3-Pin with Built-In Capacitors</a> appeared first on <a href="https://www.duomy.com">DuoMy Sensing</a>.</p>
]]></description>
										<content:encoded><![CDATA[<h2>Overview</h2>
<p>A ceramic resonator is a quartz crystal with a wider tolerance and a much lower price, and the three-pin version has the load capacitors built into the package. For a microcontroller that talks to a display and a relay board, ±0.5% is enough: the UART stays in sync because both ends are on the same clock, and nothing else in the system cares.</p>
<p>It is not enough for anything that has to agree with the outside world on time: Ethernet, USB, RTC or a radio protocol all need the accuracy of a quartz crystal. That is the decision point, not the price.</p>
<h2>Key features</h2>
<ul>
<li>Built-in load capacitors, no external parts</li>
<li>±0.5% tolerance, adequate for asynchronous UART links</li>
<li>Reliable start-up at low drive levels</li>
<li>Three-pin through-hole package</li>
<li>Lower cost than a quartz crystal</li>
</ul>
<h2>Typical applications</h2>
<ul>
<li>Microcontroller clocks in cost-sensitive products</li>
<li>Appliance and HVAC control boards</li>
<li>Display and keypad controllers</li>
<li>Non-critical serial links</li>
</ul>
<h2>Selection note</h2>
<p>Do not use a resonator for Ethernet, USB, RTC or any radio protocol. Those need quartz accuracy, and the failure appears as intermittent link drops rather than an obvious fault.</p>
<h2>Ordering</h2>
<p>Send the frequency, the accuracy the protocol needs and the package preference. We confirm whether a resonator is adequate or a crystal is required, then quote.</p>
<p>The post <a href="https://www.duomy.com/products/16mhz-ceramic-resonator-3pin/">16 MHz Ceramic Resonator, 3-Pin with Built-In Capacitors</a> appeared first on <a href="https://www.duomy.com">DuoMy Sensing</a>.</p>
]]></content:encoded>
					
		
		
			</item>
		<item>
		<title>8 MHz Crystal, 3.2 × 2.5 mm, ±10 ppm</title>
		<link>https://www.duomy.com/products/8mhz-crystal-3225/</link>
		
		<dc:creator><![CDATA[]]></dc:creator>
		<pubDate>Fri, 20 Nov 2026 01:17:24 +0000</pubDate>
				<guid isPermaLink="false">https://www.duomy.com/products/8mhz-crystal-3225/</guid>

					<description><![CDATA[<p>Surface-mount quartz crystal, 8 MHz, ±10 ppm, 18 pF load capacitance, 3.2 × 2.5 mm. Main clock reference for microcontrollers and general-purpose digital circuits.</p>
<p>The post <a href="https://www.duomy.com/products/8mhz-crystal-3225/">8 MHz Crystal, 3.2 × 2.5 mm, ±10 ppm</a> appeared first on <a href="https://www.duomy.com">DuoMy Sensing</a>.</p>
]]></description>
										<content:encoded><![CDATA[<h2>Overview</h2>
<p>Eight megahertz is the classic microcontroller clock: high enough for a useful instruction rate, low enough that the oscillator circuit is forgiving and the harmonics stay out of the way. In a 3.2 × 2.5 mm package it takes less board area than the decoupling capacitor next to it.</p>
<p>Sixty ohms of ESR is the number the oscillator amplifier has to drive. A marginal drive level shows up as slow start-up at cold temperature or as a clock that stops when the supply ramps slowly, both of which are layout and load-capacitance problems rather than crystal problems.</p>
<h2>Key features</h2>
<ul>
<li>8 MHz fundamental mode, ±10 ppm</li>
<li>18 pF load capacitance</li>
<li>3.2 × 2.5 mm SMD package</li>
<li>60 Ω maximum ESR for reliable start-up</li>
<li>±3 ppm per year aging</li>
</ul>
<h2>Typical applications</h2>
<ul>
<li>Microcontroller main clock</li>
<li>General-purpose digital timing</li>
<li>USB full-speed reference with a PLL</li>
<li>Industrial controllers and meters</li>
</ul>
<h2>Selection note</h2>
<p>Keep the crystal traces short and away from switching nodes, and connect the ground pads of the load capacitors directly to the oscillator ground. A long return path adds stray capacitance and jitter.</p>
<h2>Ordering</h2>
<p>Send the frequency, load capacitance and accuracy class. We confirm the part and the matching capacitors, then quote.</p>
<p>The post <a href="https://www.duomy.com/products/8mhz-crystal-3225/">8 MHz Crystal, 3.2 × 2.5 mm, ±10 ppm</a> appeared first on <a href="https://www.duomy.com">DuoMy Sensing</a>.</p>
]]></content:encoded>
					
		
		
			</item>
	</channel>
</rss>
