<?xml version="1.0" encoding="UTF-8"?><rss version="2.0"
	xmlns:content="http://purl.org/rss/1.0/modules/content/"
	xmlns:wfw="http://wellformedweb.org/CommentAPI/"
	xmlns:dc="http://purl.org/dc/elements/1.1/"
	xmlns:atom="http://www.w3.org/2005/Atom"
	xmlns:sy="http://purl.org/rss/1.0/modules/syndication/"
	xmlns:slash="http://purl.org/rss/1.0/modules/slash/"
	>

<channel>
	<title>Connectors &amp; Electromechanical | Sensors &amp; Electronic Components - DuoMy</title>
	<atom:link href="https://www.duomy.com/product-category/connectors-electromechanical/feed/" rel="self" type="application/rss+xml" />
	<link>https://www.duomy.com/product-category/connectors-electromechanical/</link>
	<description></description>
	<lastBuildDate>Fri, 20 Nov 2026 01:29:05 +0000</lastBuildDate>
	<language>en-US</language>
	<sy:updatePeriod>
	hourly	</sy:updatePeriod>
	<sy:updateFrequency>
	1	</sy:updateFrequency>
	<generator>https://wordpress.org/?v=7.1.5</generator>

<image>
	<url>https://www.duomy.com/wp-content/uploads/2026/04/cropped-电子-32x32.png</url>
	<title>Connectors &amp; Electromechanical | Sensors &amp; Electronic Components - DuoMy</title>
	<link>https://www.duomy.com/product-category/connectors-electromechanical/</link>
	<width>32</width>
	<height>32</height>
</image> 
	<item>
		<title>Illuminated Pushbutton, 16 mm, 1NO, 24 V LED, IP65</title>
		<link>https://www.duomy.com/products/illuminated-pushbutton-16mm-ip65/</link>
		
		<dc:creator><![CDATA[]]></dc:creator>
		<pubDate>Fri, 20 Nov 2026 01:29:05 +0000</pubDate>
				<guid isPermaLink="false">https://www.duomy.com/products/illuminated-pushbutton-16mm-ip65/</guid>

					<description><![CDATA[<p>16 mm panel-mount illuminated pushbutton, single normally-open contact, 3 A at 250 V AC, 24 V ring LED and IP65 front seal. For start, stop and reset functions that must be visible from across a room.</p>
<p>The post <a href="https://www.duomy.com/products/illuminated-pushbutton-16mm-ip65/">Illuminated Pushbutton, 16 mm, 1NO, 24 V LED, IP65</a> appeared first on <a href="https://www.duomy.com">DuoMy Sensing</a>.</p>
]]></description>
										<content:encoded><![CDATA[<h2>Overview</h2>
<p>An illuminated pushbutton combines the operator input and the status indication in one hole. On a wash-down panel that matters: every additional indicator is another seal to fail, and a button that lights when the pump is running removes the need for a separate lamp.</p>
<p>The IP65 rating applies to the front face only, which is what the standard describes. The rear terminals are not sealed, so the enclosure behind the panel still has to be rated for the environment. Assuming the button seals the whole panel is a common and expensive mistake.</p>
<h2>Key features</h2>
<ul>
<li>Integrated ring illumination replaces a separate indicator</li>
<li>16 mm cutout, 22 mm bezel, standard industrial footprint</li>
<li>3 A at 250 V AC contact rating for direct control</li>
<li>IP65 front seal for wash-down panels</li>
<li>Screw or spade terminals, no special tooling</li>
</ul>
<h2>Typical applications</h2>
<ul>
<li>Start, stop and reset stations</li>
<li>Pump and valve control panels</li>
<li>Machine mode selection with status feedback</li>
<li>Emergency acknowledge and alarm reset</li>
</ul>
<h2>Selection note</h2>
<p>Confirm the LED voltage against the panel supply before ordering. A 24 V button on a 12 V circuit will glow dimly and a 12 V button on 24 V will fail; both look identical from the front.</p>
<h2>Ordering</h2>
<p>Send the panel cutout, contact configuration, coil or LED voltage and required IP rating. We confirm the bezel and terminal type, then quote.</p>
<p>The post <a href="https://www.duomy.com/products/illuminated-pushbutton-16mm-ip65/">Illuminated Pushbutton, 16 mm, 1NO, 24 V LED, IP65</a> appeared first on <a href="https://www.duomy.com">DuoMy Sensing</a>.</p>
]]></content:encoded>
					
		
		
			</item>
		<item>
		<title>Slide Switch, SPDT, 2.54 mm Pitch, 500 mA, 10k Cycles</title>
		<link>https://www.duomy.com/products/slide-switch-spdt-2-54/</link>
		
		<dc:creator><![CDATA[]]></dc:creator>
		<pubDate>Fri, 20 Nov 2026 01:29:04 +0000</pubDate>
				<guid isPermaLink="false">https://www.duomy.com/products/slide-switch-spdt-2-54/</guid>

					<description><![CDATA[<p>SPDT slide switch on a 2.54 mm pitch, 500 mA at 30 V DC, 10,000 cycle life. For power and mode selection where the state must be visible at a glance and survive a power cycle.</p>
<p>The post <a href="https://www.duomy.com/products/slide-switch-spdt-2-54/">Slide Switch, SPDT, 2.54 mm Pitch, 500 mA, 10k Cycles</a> appeared first on <a href="https://www.duomy.com">DuoMy Sensing</a>.</p>
]]></description>
										<content:encoded><![CDATA[<h2>Overview</h2>
<p>A slide switch holds its position mechanically, which a pushbutton cannot. When the requirement is that a service technician can see at a glance whether the unit is in run or setup mode, and that the setting survives a power cut, a slide switch is the honest interface.</p>
<p>The rating is modest for a reason. The contacts are small and the wiping action is short, so 500 mA at 30 V is realistic and 2 A is not. For mains or motor loads, use the switch to drive a relay or a MOSFET rather than switching the load directly.</p>
<h2>Key features</h2>
<ul>
<li>Visible, mechanically held position</li>
<li>SPDT with 2.54 mm pitch, fits standard prototyping</li>
<li>500 mA at 30 V DC contact rating</li>
<li>10,000 cycle life at rated load</li>
<li>Top or side actuator, through-hole mounting</li>
</ul>
<h2>Typical applications</h2>
<ul>
<li>Run, setup and off mode selection</li>
<li>Battery and supply disconnect</li>
<li>Configuration jumpers with a visible state</li>
<li>Test and service overrides</li>
</ul>
<h2>Selection note</h2>
<p>Do not use a slide switch for a load above about half an amp. The contacts pit and the resistance rises until the switch behaves like a resistor; drive a relay or MOSFET instead.</p>
<h2>Ordering</h2>
<p>Send the load voltage and current, actuator orientation and panel thickness. We confirm the rating and mounting, then quote.</p>
<p>The post <a href="https://www.duomy.com/products/slide-switch-spdt-2-54/">Slide Switch, SPDT, 2.54 mm Pitch, 500 mA, 10k Cycles</a> appeared first on <a href="https://www.duomy.com">DuoMy Sensing</a>.</p>
]]></content:encoded>
					
		
		
			</item>
		<item>
		<title>Tactile Switch, 6 × 6 mm, SMD, 100 gf, 100k Cycles</title>
		<link>https://www.duomy.com/products/tactile-switch-6x6-smd/</link>
		
		<dc:creator><![CDATA[]]></dc:creator>
		<pubDate>Fri, 20 Nov 2026 01:29:03 +0000</pubDate>
				<guid isPermaLink="false">https://www.duomy.com/products/tactile-switch-6x6-smd/</guid>

					<description><![CDATA[<p>6 × 6 mm surface-mount tactile switch, 5 mm height, 100 gf actuation force and 100,000 cycle life. The standard part for menu navigation and reset buttons on control boards.</p>
<p>The post <a href="https://www.duomy.com/products/tactile-switch-6x6-smd/">Tactile Switch, 6 × 6 mm, SMD, 100 gf, 100k Cycles</a> appeared first on <a href="https://www.duomy.com">DuoMy Sensing</a>.</p>
]]></description>
										<content:encoded><![CDATA[<h2>Overview</h2>
<p>A tactile switch is defined by its feel and its footprint, not its electrical rating. The 6 × 6 mm package is the de facto standard because it fits under a 5 mm front panel, gives a distinct click at 100 gf and can be placed by any pick-and-place machine.</p>
<p>The failure mode that matters is contact bounce, not life. A mechanical switch makes and breaks contact several times within a few milliseconds, so firmware has to debounce in software or the switch needs a hardware RC network. Neither the datasheet life figure nor the contact rating tells you anything about bounce.</p>
<h2>Key features</h2>
<ul>
<li>6 × 6 mm body with 5 mm actuator height</li>
<li>100 gf actuation force with a tactile click</li>
<li>100,000 cycle mechanical and electrical life</li>
<li>SMD terminals with ground tab for panel stability</li>
<li>Compatible with standard 6 mm caps and actuators</li>
</ul>
<h2>Typical applications</h2>
<ul>
<li>Menu and navigation buttons</li>
<li>Reset and test inputs</li>
<li>Setpoint adjustment on control panels</li>
<li>Mode selection on handheld devices</li>
</ul>
<h2>Selection note</h2>
<p>Debounce in firmware with a 20 to 50 ms window, or fit a 100 nF capacitor across the contacts. Without one of the two, a single press will register several times on a fast microcontroller.</p>
<h2>Ordering</h2>
<p>Send the panel height, actuation force, cap style and expected press count. We confirm the height and terminal variant, then quote.</p>
<p>The post <a href="https://www.duomy.com/products/tactile-switch-6x6-smd/">Tactile Switch, 6 × 6 mm, SMD, 100 gf, 100k Cycles</a> appeared first on <a href="https://www.duomy.com">DuoMy Sensing</a>.</p>
]]></content:encoded>
					
		
		
			</item>
		<item>
		<title>Tactile Switch, 12 × 12 mm, Through-Hole, 260 gf, 500k Cycles</title>
		<link>https://www.duomy.com/products/tactile-switch-12x12-tht/</link>
		
		<dc:creator><![CDATA[]]></dc:creator>
		<pubDate>Fri, 20 Nov 2026 01:29:03 +0000</pubDate>
				<guid isPermaLink="false">https://www.duomy.com/products/tactile-switch-12x12-tht/</guid>

					<description><![CDATA[<p>12 × 12 mm through-hole tactile switch, 260 gf, 7 mm height and 500,000 cycle life. For front panels that are pressed hard, often, and with gloves on.</p>
<p>The post <a href="https://www.duomy.com/products/tactile-switch-12x12-tht/">Tactile Switch, 12 × 12 mm, Through-Hole, 260 gf, 500k Cycles</a> appeared first on <a href="https://www.duomy.com">DuoMy Sensing</a>.</p>
]]></description>
										<content:encoded><![CDATA[<h2>Overview</h2>
<p>The 12 mm through-hole switch exists for panels where the operator wears gloves: pump stations, valve control boxes, packaging lines. A 100 gf 6 mm switch feels fine on a bench and feels like nothing through a nitrile glove, so the actuator force and the travel are increased deliberately.</p>
<p>Through-hole mounting matters here too. These panels take repeated force at an angle, and a surface-mount pad will lift after enough abuse. Four through-hole pins spread the load into the board, and the switch can be replaced without a hot-air station.</p>
<h2>Key features</h2>
<ul>
<li>260 gf actuation force for gloved operation</li>
<li>500,000 cycle life, twice the small-switch rating</li>
<li>Through-hole terminals resist repeated lateral force</li>
<li>Snap-on 6 mm caps in round and square profiles</li>
<li>7 mm height suits a 3 mm front panel</li>
</ul>
<h2>Typical applications</h2>
<ul>
<li>Industrial control panels</li>
<li>Pump and valve station pushbuttons</li>
<li>Packaging and food line operator stations</li>
<li>Outdoor equipment with gloved operation</li>
</ul>
<h2>Selection note</h2>
<p>Allow for panel thickness when choosing cap height. A 7 mm switch behind a 3 mm panel leaves 4 mm of actuator, which is enough for most caps but not for the taller illuminated types.</p>
<h2>Ordering</h2>
<p>Send the panel thickness, cap style, actuation force and press count. We confirm height and terminal configuration, then quote.</p>
<p>The post <a href="https://www.duomy.com/products/tactile-switch-12x12-tht/">Tactile Switch, 12 × 12 mm, Through-Hole, 260 gf, 500k Cycles</a> appeared first on <a href="https://www.duomy.com">DuoMy Sensing</a>.</p>
]]></content:encoded>
					
		
		
			</item>
		<item>
		<title>Solid-State Relay, 25 A 240 V AC, Zero-Cross</title>
		<link>https://www.duomy.com/products/ssr-25a-240vac-zero-cross/</link>
		
		<dc:creator><![CDATA[]]></dc:creator>
		<pubDate>Fri, 20 Nov 2026 01:18:13 +0000</pubDate>
				<guid isPermaLink="false">https://www.duomy.com/products/ssr-25a-240vac-zero-cross/</guid>

					<description><![CDATA[<p>Panel-mount solid-state relay, 25 A at 24 to 280 V AC, zero-cross switching, 3 to 32 V DC control. No contacts to wear, no coil, no switching arc.</p>
<p>The post <a href="https://www.duomy.com/products/ssr-25a-240vac-zero-cross/">Solid-State Relay, 25 A 240 V AC, Zero-Cross</a> appeared first on <a href="https://www.duomy.com">DuoMy Sensing</a>.</p>
]]></description>
										<content:encoded><![CDATA[<h2>Overview</h2>
<p>A solid-state relay has no moving contact, so it does not arc, does not weld, and does not wear out from switching. Zero-cross turn-on means it waits for the mains voltage to pass through zero before conducting, which removes the current surge that a mechanical contact produces into a capacitive or lamp load.</p>
<p>The two specifications that decide the application are leakage and heat. Ten milliamps of off-state leakage is enough to keep a small lamp glowing faintly, and 25 A at 1.6 V is 40 W of dissipation that has to leave through the baseplate into a heatsink.</p>
<h2>Key features</h2>
<ul>
<li>Zero-cross switching for low inrush</li>
<li>25 A at up to 280 V AC</li>
<li>4,000 V AC isolation</li>
<li>No contacts to wear or weld</li>
<li>3 to 32 V DC control input</li>
</ul>
<h2>Typical applications</h2>
<ul>
<li>Heater and oven element control</li>
<li>High-cycle switching applications</li>
<li>Equipment in dusty or explosive atmospheres</li>
<li>Lamp and capacitive load switching</li>
</ul>
<h2>Selection note</h2>
<p>A solid-state relay needs a heatsink. At 25 A the dissipation is around 40 W, and the baseplate temperature determines the life of the internal semiconductor.</p>
<h2>Ordering</h2>
<p>Send the load voltage, current, duty cycle and cooling arrangement. We size the heatsink with the relay, then quote.</p>
<p>The post <a href="https://www.duomy.com/products/ssr-25a-240vac-zero-cross/">Solid-State Relay, 25 A 240 V AC, Zero-Cross</a> appeared first on <a href="https://www.duomy.com">DuoMy Sensing</a>.</p>
]]></content:encoded>
					
		
		
			</item>
		<item>
		<title>12 V Power Relay, SPDT, 10 A 250 V AC, PCB Mount</title>
		<link>https://www.duomy.com/products/12v-power-relay-spdt-10a-pcb/</link>
		
		<dc:creator><![CDATA[]]></dc:creator>
		<pubDate>Fri, 20 Nov 2026 01:18:12 +0000</pubDate>
				<guid isPermaLink="false">https://www.duomy.com/products/12v-power-relay-spdt-10a-pcb/</guid>

					<description><![CDATA[<p>PCB power relay, 12 V coil, SPDT contacts rated 10 A at 250 V AC, sealed case. Switching mains loads from a low-voltage control circuit.</p>
<p>The post <a href="https://www.duomy.com/products/12v-power-relay-spdt-10a-pcb/">12 V Power Relay, SPDT, 10 A 250 V AC, PCB Mount</a> appeared first on <a href="https://www.duomy.com">DuoMy Sensing</a>.</p>
]]></description>
										<content:encoded><![CDATA[<h2>Overview</h2>
<p>A 10 A contact rating at 250 V AC is the workhorse specification: pumps, heaters, contactor coils, lamps. The relay gives a low-voltage controller a way to switch a mains load with a 1,500 V AC barrier between the two circuits and no leakage current.</p>
<p>The contact rating depends on the load type. A resistive 10 A load is what the data sheet means; a motor or a capacitive load draws a surge at switch-on and derates the rating substantially. Where the load is inductive, an RC snubber across the contacts extends life.</p>
<h2>Key features</h2>
<ul>
<li>10 A at 250 V AC contact rating</li>
<li>12 V coil, 360 mW</li>
<li>1,500 V AC coil-to-contact isolation</li>
<li>100,000 electrical operations at rated load</li>
<li>Sealed case, PCB mounting</li>
</ul>
<h2>Typical applications</h2>
<ul>
<li>Pump and heater switching</li>
<li>Lighting and lamp loads</li>
<li>Contactor and valve coil driving</li>
<li>Appliance mains switching</li>
</ul>
<h2>Selection note</h2>
<p>Derate the contact rating for inductive or capacitive loads. A 10 A resistive rating does not mean a 10 A motor, and a snubber across the contacts is cheap insurance.</p>
<h2>Ordering</h2>
<p>Send the coil voltage, load type, current and voltage. We confirm the rating against the load and recommend suppression, then quote.</p>
<p>The post <a href="https://www.duomy.com/products/12v-power-relay-spdt-10a-pcb/">12 V Power Relay, SPDT, 10 A 250 V AC, PCB Mount</a> appeared first on <a href="https://www.duomy.com">DuoMy Sensing</a>.</p>
]]></content:encoded>
					
		
		
			</item>
		<item>
		<title>24 V DPDT Relay, 5 A, Sealed, PCB Mount</title>
		<link>https://www.duomy.com/products/24v-dpdt-relay-5a-sealed/</link>
		
		<dc:creator><![CDATA[]]></dc:creator>
		<pubDate>Fri, 20 Nov 2026 01:18:12 +0000</pubDate>
				<guid isPermaLink="false">https://www.duomy.com/products/24v-dpdt-relay-5a-sealed/</guid>

					<description><![CDATA[<p>Sealed PCB relay, 24 V coil, DPDT contacts rated 5 A at 250 V AC, with manual test button and mechanical flag. Two independent changeover contacts from one coil.</p>
<p>The post <a href="https://www.duomy.com/products/24v-dpdt-relay-5a-sealed/">24 V DPDT Relay, 5 A, Sealed, PCB Mount</a> appeared first on <a href="https://www.duomy.com">DuoMy Sensing</a>.</p>
]]></description>
										<content:encoded><![CDATA[<h2>Overview</h2>
<p>Two changeover contacts from one coil is what makes a DPDT relay useful in a control panel: switch a live and a neutral together, or reverse a small DC motor by swapping polarity, with one signal from the controller.</p>
<p>The manual test button and mechanical flag are commissioning aids. A technician can operate the relay without energising the coil and see the contact state from outside the enclosure, which shortens fault finding considerably on a machine with a dozen relays.</p>
<h2>Key features</h2>
<ul>
<li>DPDT contacts, 5 A at 250 V AC</li>
<li>24 V coil, 360 mW</li>
<li>Manual test button and mechanical flag</li>
<li>1,500 V AC coil-to-contact isolation</li>
<li>Sealed case for washdown environments</li>
</ul>
<h2>Typical applications</h2>
<ul>
<li>Motor polarity reversal on small actuators</li>
<li>Switching live and neutral together</li>
<li>Control panel logic with two circuits</li>
<li>Equipment with commissioning test requirements</li>
</ul>
<h2>Selection note</h2>
<p>Do not use the manual test button as an operating control. It is rated for occasional actuation during commissioning, not for repeated use under load.</p>
<h2>Ordering</h2>
<p>Send the coil voltage, contact configuration and load. We confirm the rating and the test-button option, then quote.</p>
<p>The post <a href="https://www.duomy.com/products/24v-dpdt-relay-5a-sealed/">24 V DPDT Relay, 5 A, Sealed, PCB Mount</a> appeared first on <a href="https://www.duomy.com">DuoMy Sensing</a>.</p>
]]></content:encoded>
					
		
		
			</item>
		<item>
		<title>5 V Signal Relay, SPDT, 1 A, DIP</title>
		<link>https://www.duomy.com/products/5v-signal-relay-spdt-dip/</link>
		
		<dc:creator><![CDATA[]]></dc:creator>
		<pubDate>Fri, 20 Nov 2026 01:18:11 +0000</pubDate>
				<guid isPermaLink="false">https://www.duomy.com/products/5v-signal-relay-spdt-dip/</guid>

					<description><![CDATA[<p>Sealed signal relay, 5 V coil, SPDT contacts rated 1 A at 30 V DC, DIP footprint. Low-level signal switching with complete galvanic separation between coil and contact.</p>
<p>The post <a href="https://www.duomy.com/products/5v-signal-relay-spdt-dip/">5 V Signal Relay, SPDT, 1 A, DIP</a> appeared first on <a href="https://www.duomy.com">DuoMy Sensing</a>.</p>
]]></description>
										<content:encoded><![CDATA[<h2>Overview</h2>
<p>A signal relay switches a small load while providing a real galvanic gap between the coil circuit and the contacts. That gap is what a semiconductor cannot offer: no leakage path, no common-mode coupling, no failure mode that conducts in both directions.</p>
<p>At 1 A and 30 V DC it suits instrumentation switching, a solenoid valve pilot, or a signal path that has to be physically opened for safety. Above that current a power relay is the right part, and the package grows accordingly.</p>
<h2>Key features</h2>
<ul>
<li>5 V coil, 140 mW, 178 Ω</li>
<li>SPDT contacts rated 1 A at 30 V DC</li>
<li>5 ms operate time, 3 ms release</li>
<li>100 million mechanical operations</li>
<li>Sealed body for wave soldering and washing</li>
</ul>
<h2>Typical applications</h2>
<ul>
<li>Instrumentation signal switching</li>
<li>Pilot duty for small valves and actuators</li>
<li>Safety-related circuit isolation</li>
<li>Test equipment channel selection</li>
</ul>
<h2>Selection note</h2>
<p>Fit a flyback diode across the coil. The inductive kick from a 5 V coil is enough to destroy the driving transistor and to radiate into nearby signal traces.</p>
<h2>Ordering</h2>
<p>Send the coil voltage, contact configuration and load. We confirm the contact rating against the load type, then quote.</p>
<p>The post <a href="https://www.duomy.com/products/5v-signal-relay-spdt-dip/">5 V Signal Relay, SPDT, 1 A, DIP</a> appeared first on <a href="https://www.duomy.com">DuoMy Sensing</a>.</p>
]]></content:encoded>
					
		
		
			</item>
		<item>
		<title>5 × 20 mm Glass Cartridge Fuse, 6.3 A 250 V, Time-Lag</title>
		<link>https://www.duomy.com/products/5x20-glass-cartridge-fuse-63a/</link>
		
		<dc:creator><![CDATA[]]></dc:creator>
		<pubDate>Fri, 20 Nov 2026 01:06:39 +0000</pubDate>
				<guid isPermaLink="false">https://www.duomy.com/products/5x20-glass-cartridge-fuse-63a/</guid>

					<description><![CDATA[<p>5 × 20 mm glass cartridge fuse, 6.3 A, 250 V AC, time-lag characteristic, 150 A breaking capacity. Mains input protection in equipment with a replaceable fuse holder.</p>
<p>The post <a href="https://www.duomy.com/products/5x20-glass-cartridge-fuse-63a/">5 × 20 mm Glass Cartridge Fuse, 6.3 A 250 V, Time-Lag</a> appeared first on <a href="https://www.duomy.com">DuoMy Sensing</a>.</p>
]]></description>
										<content:encoded><![CDATA[<h2>Overview</h2>
<p>A glass cartridge fuse in a panel holder is the classic mains input protection: visible, replaceable without desoldering, and cheap enough that every piece of equipment can have one. The time-lag characteristic absorbs the inrush of a transformer or a switching supply without opening on every switch-on.</p>
<p>The glass body is also the diagnostic. A blown fuse can be seen through the tube, and whether the element is melted with a bead or sprayed on the glass tells a technician whether the fault was a slow overload or a hard short.</p>
<h2>Key features</h2>
<ul>
<li>Time-lag characteristic for transformer and SMPS inrush</li>
<li>250 V AC, 6.3 A, 150 A breaking capacity</li>
<li>Glass body for visual fault inspection</li>
<li>IEC 60127-2 sheet 3 dimensions</li>
<li>Nickel-plated brass end caps</li>
</ul>
<h2>Typical applications</h2>
<ul>
<li>Mains input protection in panel-mounted equipment</li>
<li>Transformer primary protection</li>
<li>Switching supply input protection</li>
<li>Laboratory and test equipment</li>
</ul>
<h2>Selection note</h2>
<p>Never fit a higher-rated fuse to stop repeat failures. A fuse that opens repeatedly is reporting a fault, and the next component to fail will be more expensive.</p>
<h2>Ordering</h2>
<p>Send the input voltage, steady current and inrush profile, plus the holder type. We confirm the characteristic and breaking capacity, then quote per box.</p>
<p>The post <a href="https://www.duomy.com/products/5x20-glass-cartridge-fuse-63a/">5 × 20 mm Glass Cartridge Fuse, 6.3 A 250 V, Time-Lag</a> appeared first on <a href="https://www.duomy.com">DuoMy Sensing</a>.</p>
]]></content:encoded>
					
		
		
			</item>
		<item>
		<title>PTC Resettable Fuse, 1.1 A 60 V, Radial</title>
		<link>https://www.duomy.com/products/ptc-resettable-fuse-11a-60v/</link>
		
		<dc:creator><![CDATA[]]></dc:creator>
		<pubDate>Fri, 20 Nov 2026 01:06:39 +0000</pubDate>
				<guid isPermaLink="false">https://www.duomy.com/products/ptc-resettable-fuse-11a-60v/</guid>

					<description><![CDATA[<p>Radial polymer PTC resettable fuse, 1.1 A hold current, 60 V, 2.2 A trip current. Self-resetting overcurrent protection for ports and low-voltage branches.</p>
<p>The post <a href="https://www.duomy.com/products/ptc-resettable-fuse-11a-60v/">PTC Resettable Fuse, 1.1 A 60 V, Radial</a> appeared first on <a href="https://www.duomy.com">DuoMy Sensing</a>.</p>
]]></description>
										<content:encoded><![CDATA[<h2>Overview</h2>
<p>A PTC does not blow; it heats, changes resistance by orders of magnitude, and holds the current to a trickle until the fault is removed. That behaviour suits ports and branches where a technician cannot reach a fuse, and where an intermittent fault should not require a service call.</p>
<p>The catch is that a PTC is a thermal device. Hold current falls as ambient rises, so a part rated 1.1 A at 25 °C may only hold 0.7 A at 70 °C. Derate for the real enclosure temperature, and remember that the device stays warm and resistive for a while after the fault clears.</p>
<h2>Key features</h2>
<ul>
<li>Self-resetting, no replacement needed</li>
<li>1.1 A hold, 2.2 A trip current at 25 °C</li>
<li>60 V maximum, 40 A fault current capability</li>
<li>Radial package with 5.1 mm lead spacing</li>
<li>Automatic recovery once the fault is removed</li>
</ul>
<h2>Typical applications</h2>
<ul>
<li>Port and interface overcurrent protection</li>
<li>Low-voltage branch protection in enclosures</li>
<li>Motor stall protection on small actuators</li>
<li>Equipment in inaccessible locations</li>
</ul>
<h2>Selection note</h2>
<p>Derate the hold current for ambient temperature. At 70 °C, expect roughly 60% of the 25 °C rating, and check the derating curve before choosing the part.</p>
<h2>Ordering</h2>
<p>Send the normal current, trip current required, maximum voltage and ambient temperature. We apply the derating curve and quote the resulting part.</p>
<p>The post <a href="https://www.duomy.com/products/ptc-resettable-fuse-11a-60v/">PTC Resettable Fuse, 1.1 A 60 V, Radial</a> appeared first on <a href="https://www.duomy.com">DuoMy Sensing</a>.</p>
]]></content:encoded>
					
		
		
			</item>
	</channel>
</rss>
