<?xml version="1.0" encoding="UTF-8"?><rss version="2.0"
	xmlns:content="http://purl.org/rss/1.0/modules/content/"
	xmlns:wfw="http://wellformedweb.org/CommentAPI/"
	xmlns:dc="http://purl.org/dc/elements/1.1/"
	xmlns:atom="http://www.w3.org/2005/Atom"
	xmlns:sy="http://purl.org/rss/1.0/modules/syndication/"
	xmlns:slash="http://purl.org/rss/1.0/modules/slash/"
	>

<channel>
	<title>Power Discretes &amp; Modules | Sensors &amp; Electronic Components - DuoMy</title>
	<atom:link href="https://www.duomy.com/product-category/discrete-power/feed/" rel="self" type="application/rss+xml" />
	<link>https://www.duomy.com/product-category/discrete-power/</link>
	<description></description>
	<lastBuildDate>Fri, 20 Nov 2026 01:28:56 +0000</lastBuildDate>
	<language>en-US</language>
	<sy:updatePeriod>
	hourly	</sy:updatePeriod>
	<sy:updateFrequency>
	1	</sy:updateFrequency>
	<generator>https://wordpress.org/?v=7.1.5</generator>

<image>
	<url>https://www.duomy.com/wp-content/uploads/2026/04/cropped-电子-32x32.png</url>
	<title>Power Discretes &amp; Modules | Sensors &amp; Electronic Components - DuoMy</title>
	<link>https://www.duomy.com/product-category/discrete-power/</link>
	<width>32</width>
	<height>32</height>
</image> 
	<item>
		<title>NPN Power Transistor, 100 V, 6 A, TO-220</title>
		<link>https://www.duomy.com/products/npn-power-100v-6a-to220/</link>
		
		<dc:creator><![CDATA[]]></dc:creator>
		<pubDate>Fri, 20 Nov 2026 01:28:56 +0000</pubDate>
				<guid isPermaLink="false">https://www.duomy.com/products/npn-power-100v-6a-to220/</guid>

					<description><![CDATA[<p>Power NPN in TO-220, 100 V VCEO and 6 A continuous, 65 W dissipation. Used as a series pass element, relay driver and linear regulator output stage where a switching converter is not justified.</p>
<p>The post <a href="https://www.duomy.com/products/npn-power-100v-6a-to220/">NPN Power Transistor, 100 V, 6 A, TO-220</a> appeared first on <a href="https://www.duomy.com">DuoMy Sensing</a>.</p>
]]></description>
										<content:encoded><![CDATA[<h2>Overview</h2>
<p>A 100 V power bipolar is what gets used when a linear stage has to survive a 48 V rail and a short circuit at the output. It is slower and less efficient than a MOSFET, but it is far harder to destroy: the safe operating area is wide and the part does not fail from a single gate transient.</p>
<p>The limiting factor is thermal, not electrical. At 6 A and 1.5 V saturation the device dissipates 9 W, which on a TO-220 needs a heatsink of about 5 °C/W to stay below a 100 °C junction in 40 °C air. The 65 W rating on the datasheet assumes the case is held at 25 °C, which never happens without forced cooling.</p>
<h2>Key features</h2>
<ul>
<li>VCEO 100 V, 6 A continuous, 10 A peak</li>
<li>Low saturation voltage for a power bipolar</li>
<li>TO-220 with isolated mounting option</li>
<li>Wide safe operating area, tolerant of short-circuit events</li>
<li>Gain 15 minimum at 3 A, enough for direct base drive from a driver IC</li>
</ul>
<h2>Typical applications</h2>
<ul>
<li>Linear regulator pass elements</li>
<li>Relay, solenoid and valve drivers</li>
<li>Lamp and heater switching</li>
<li>Constant-current discharge circuits</li>
</ul>
<h2>Selection note</h2>
<p>Compute dissipation before choosing a heatsink. A 24 V rail dropping to 12 V at 3 A dissipates 36 W in the transistor, which no TO-220 survives without forced air. In that case a switching converter is the correct answer.</p>
<h2>Ordering</h2>
<p>Send the rail voltage, load current, duty cycle and ambient temperature. We confirm the thermal calculation and heatsink requirement, then quote.</p>
<p>The post <a href="https://www.duomy.com/products/npn-power-100v-6a-to220/">NPN Power Transistor, 100 V, 6 A, TO-220</a> appeared first on <a href="https://www.duomy.com">DuoMy Sensing</a>.</p>
]]></content:encoded>
					
		
		
			</item>
		<item>
		<title>NPN Darlington Transistor, 100 V, 8 A, hFE 1000, TO-220</title>
		<link>https://www.duomy.com/products/npn-darlington-100v-8a-to220/</link>
		
		<dc:creator><![CDATA[]]></dc:creator>
		<pubDate>Fri, 20 Nov 2026 01:28:56 +0000</pubDate>
				<guid isPermaLink="false">https://www.duomy.com/products/npn-darlington-100v-8a-to220/</guid>

					<description><![CDATA[<p>Monolithic NPN Darlington in TO-220, 100 V and 8 A, with minimum gain of 1000 so a logic pin can drive it directly. For relay, solenoid and motor loads that need high current gain rather than low saturation voltage.</p>
<p>The post <a href="https://www.duomy.com/products/npn-darlington-100v-8a-to220/">NPN Darlington Transistor, 100 V, 8 A, hFE 1000, TO-220</a> appeared first on <a href="https://www.duomy.com">DuoMy Sensing</a>.</p>
]]></description>
										<content:encoded><![CDATA[<h2>Overview</h2>
<p>A Darlington is two transistors in series inside one package. The gain multiplies, so 3 mA of base current controls 3 A of collector current, which means a microcontroller pin drives the load through one resistor and nothing else.</p>
<p>The price is a saturation voltage of about 2 V instead of 0.3 V. At 3 A that is 6 W in the device, so a Darlington belongs on loads that switch infrequently and can tolerate the lost rail voltage. For a 24 V relay coil the 2 V drop is irrelevant; for a 5 V motor it is 40 percent of the supply.</p>
<h2>Key features</h2>
<ul>
<li>Minimum gain 1000 lets a logic pin drive 3 A directly</li>
<li>VCEO 100 V, 8 A continuous</li>
<li>Integrated base-emitter resistors reduce leakage and part count</li>
<li>TO-220 package with standard heatsink mounting</li>
<li>Slower switching is an advantage on noisy inductive loads</li>
</ul>
<h2>Typical applications</h2>
<ul>
<li>Relay and contactor coil drive</li>
<li>Solenoid and valve actuation</li>
<li>Automotive lamp and accessory switching</li>
<li>Low-frequency motor control</li>
</ul>
<h2>Selection note</h2>
<p>A Darlington cannot pull its collector below about 1 V, so it is the wrong choice for a low-voltage rail. Above 12 V the 2 V drop costs little; at 5 V it may leave the load under its minimum operating voltage.</p>
<h2>Ordering</h2>
<p>Send the load voltage, current, switching frequency and drive source. We confirm whether a Darlington or a MOSFET fits the duty cycle, then quote.</p>
<p>The post <a href="https://www.duomy.com/products/npn-darlington-100v-8a-to220/">NPN Darlington Transistor, 100 V, 8 A, hFE 1000, TO-220</a> appeared first on <a href="https://www.duomy.com">DuoMy Sensing</a>.</p>
]]></content:encoded>
					
		
		
			</item>
		<item>
		<title>PNP Small-Signal Transistor, 40 V, 200 mA, SOT-23</title>
		<link>https://www.duomy.com/products/pnp-small-signal-40v-200ma-sot23/</link>
		
		<dc:creator><![CDATA[]]></dc:creator>
		<pubDate>Fri, 20 Nov 2026 01:28:55 +0000</pubDate>
				<guid isPermaLink="false">https://www.duomy.com/products/pnp-small-signal-40v-200ma-sot23/</guid>

					<description><![CDATA[<p>Complementary PNP in SOT-23, 40 V and 200 mA, for high-side switching and push-pull output stages. Matched to the NPN part in the same series for symmetrical drive circuits.</p>
<p>The post <a href="https://www.duomy.com/products/pnp-small-signal-40v-200ma-sot23/">PNP Small-Signal Transistor, 40 V, 200 mA, SOT-23</a> appeared first on <a href="https://www.duomy.com">DuoMy Sensing</a>.</p>
]]></description>
										<content:encoded><![CDATA[<h2>Overview</h2>
<p>A PNP switches the positive rail. That matters when the load must sit at ground potential rather than floating above a low-side switch, which is the usual requirement for sensors, shielded enclosures and anything with an exposed metal body.</p>
<p>The cost of high-side switching with a bipolar is that the base must be pulled below the emitter, so the drive signal has to swing to the supply rail. Driving a PNP from a 3.3 V pin on a 24 V rail needs an extra NPN or a level shifter in front of it. For low duty cycles and modest currents that is still cheaper and quieter than a P-channel MOSFET with its gate charge.</p>
<h2>Key features</h2>
<ul>
<li>Complementary to the NPN part for push-pull stages</li>
<li>VCEO −40 V, 200 mA continuous</li>
<li>Low saturation voltage keeps the load at full rail voltage</li>
<li>SOT-23 footprint shared with the NPN counterpart</li>
<li>Gain bins available for matched-pair use</li>
</ul>
<h2>Typical applications</h2>
<ul>
<li>High-side load switching</li>
<li>Push-pull and class-AB output stages</li>
<li>Current sources and active loads</li>
<li>Signal clamping and discharge paths</li>
</ul>
<h2>Selection note</h2>
<p>For high-side switching from a lower-voltage logic pin, add an NPN inverter in front of the base. A direct connection will leave the PNP permanently on or permanently off depending on the rail ratio.</p>
<h2>Ordering</h2>
<p>Send the rail voltage, load current, drive source and whether the load must reference ground. We confirm polarity, gain bin and package, then quote.</p>
<p>The post <a href="https://www.duomy.com/products/pnp-small-signal-40v-200ma-sot23/">PNP Small-Signal Transistor, 40 V, 200 mA, SOT-23</a> appeared first on <a href="https://www.duomy.com">DuoMy Sensing</a>.</p>
]]></content:encoded>
					
		
		
			</item>
		<item>
		<title>NPN Small-Signal Transistor, 40 V, 200 mA, SOT-23</title>
		<link>https://www.duomy.com/products/npn-small-signal-40v-200ma-sot23/</link>
		
		<dc:creator><![CDATA[]]></dc:creator>
		<pubDate>Fri, 20 Nov 2026 01:28:54 +0000</pubDate>
				<guid isPermaLink="false">https://www.duomy.com/products/npn-small-signal-40v-200ma-sot23/</guid>

					<description><![CDATA[<p>General-purpose NPN in SOT-23, 40 V VCEO and 200 mA continuous collector current. The default part for level shifting, LED drive and low-side switching on 12 V and 24 V control rails.</p>
<p>The post <a href="https://www.duomy.com/products/npn-small-signal-40v-200ma-sot23/">NPN Small-Signal Transistor, 40 V, 200 mA, SOT-23</a> appeared first on <a href="https://www.duomy.com">DuoMy Sensing</a>.</p>
]]></description>
										<content:encoded><![CDATA[<h2>Overview</h2>
<p>The 40 V / 200 mA SOT-23 NPN is the part that fills the gaps between a microcontroller pin and a load. A GPIO sources a few milliamps at 3.3 V; a relay coil, a small solenoid or a backlight string needs tens of milliamps at 12 V or 24 V. One transistor and two resistors bridge that gap.</p>
<p>The number that decides whether the circuit works is not hFE on the datasheet front page but hFE at the actual collector current. Gain falls at low current and again at high current, so a part specified at 100 minimum should be driven with roughly twice the base current the nominal gain implies. That is what keeps the transistor in saturation when the batch is cold and the gain is at the bottom of its bin.</p>
<h2>Key features</h2>
<ul>
<li>VCEO 40 V covers 24 V rails with margin for inductive kickback</li>
<li>200 mA continuous, 500 mA pulsed collector current</li>
<li>hFE 100 to 300 at 10 mA, sorted into gain bins on request</li>
<li>VCE(sat) 0.2 V typical at 10 mA, so dissipation stays under 10 mW</li>
<li>Standard SOT-23 footprint, pin-compatible with common generic parts</li>
</ul>
<h2>Typical applications</h2>
<ul>
<li>Relay and solenoid coil drivers</li>
<li>LED and backlight current switching</li>
<li>Logic level translation between 3.3 V and 12 V domains</li>
<li>Signal inversion and simple analogue amplification</li>
</ul>
<h2>Selection note</h2>
<p>Add a base-emitter resistor of 10 kΩ to hold the transistor off when the driving pin is floating or tristated during reset. Without it, a controller in reset can switch the load on through leakage.</p>
<h2>Ordering</h2>
<p>Send the load voltage, load current, drive voltage and switching frequency. We confirm gain bin and package, then quote.</p>
<p>The post <a href="https://www.duomy.com/products/npn-small-signal-40v-200ma-sot23/">NPN Small-Signal Transistor, 40 V, 200 mA, SOT-23</a> appeared first on <a href="https://www.duomy.com">DuoMy Sensing</a>.</p>
]]></content:encoded>
					
		
		
			</item>
		<item>
		<title>20 W Wide-Input Isolated DC-DC, 9–36 V to 12 V</title>
		<link>https://www.duomy.com/products/20w-wide-input-isolated-dc-dc-9-36v-12v/</link>
		
		<dc:creator><![CDATA[]]></dc:creator>
		<pubDate>Fri, 20 Nov 2026 01:18:00 +0000</pubDate>
				<guid isPermaLink="false">https://www.duomy.com/products/20w-wide-input-isolated-dc-dc-9-36v-12v/</guid>

					<description><![CDATA[<p>Isolated DC-DC converter module, 9 to 36 V input, 12 V 1.67 A output, 1.5 kV isolation, DIP-6 package. Wide input range covers 12 V and 24 V systems with one part.</p>
<p>The post <a href="https://www.duomy.com/products/20w-wide-input-isolated-dc-dc-9-36v-12v/">20 W Wide-Input Isolated DC-DC, 9–36 V to 12 V</a> appeared first on <a href="https://www.duomy.com">DuoMy Sensing</a>.</p>
]]></description>
										<content:encoded><![CDATA[<h2>Overview</h2>
<p>A 9 to 36 V input window covers a 12 V battery with sag, a 24 V industrial rail with surge, and everything between, so one part number serves several product variants. That is the practical reason wide-input modules exist: fewer line items, fewer spares, one qualification.</p>
<p>At 88% efficiency and 20 W, the module dissipates about 2.7 W, which the DIP package sheds through its pins and the surrounding copper. It is a component to be placed with airflow in mind rather than tucked into a corner.</p>
<h2>Key features</h2>
<ul>
<li>9 to 36 V input covers 12 V and 24 V systems</li>
<li>12 V 1.67 A isolated output</li>
<li>88% efficiency at full load</li>
<li>DIP-6 package with through-hole pins</li>
<li>Short-circuit and over-voltage protected</li>
</ul>
<h2>Typical applications</h2>
<ul>
<li>24 V industrial rail to 12 V isolated rail</li>
<li>Vehicle and battery-powered equipment</li>
<li>Communication gateway supplies</li>
<li>Instrumentation with floating outputs</li>
</ul>
<h2>Selection note</h2>
<p>Add input and output capacitors as shown in the data sheet, even though the module works without them. They are what keeps the ripple inside the specification over temperature.</p>
<h2>Ordering</h2>
<p>Send the input range, output voltage and current, and the ambient. We confirm derating and the filter components, then quote.</p>
<p>The post <a href="https://www.duomy.com/products/20w-wide-input-isolated-dc-dc-9-36v-12v/">20 W Wide-Input Isolated DC-DC, 9–36 V to 12 V</a> appeared first on <a href="https://www.duomy.com">DuoMy Sensing</a>.</p>
]]></content:encoded>
					
		
		
			</item>
		<item>
		<title>600 V 10 A Intelligent Power Module, Three-Phase</title>
		<link>https://www.duomy.com/products/600v-10a-ipm-three-phase/</link>
		
		<dc:creator><![CDATA[]]></dc:creator>
		<pubDate>Fri, 20 Nov 2026 01:18:00 +0000</pubDate>
				<guid isPermaLink="false">https://www.duomy.com/products/600v-10a-ipm-three-phase/</guid>

					<description><![CDATA[<p>Intelligent power module, 600 V 10 A, three-phase inverter with gate drivers, bootstrap supply and protection integrated. Six switches, one part number, protected output stage.</p>
<p>The post <a href="https://www.duomy.com/products/600v-10a-ipm-three-phase/">600 V 10 A Intelligent Power Module, Three-Phase</a> appeared first on <a href="https://www.duomy.com">DuoMy Sensing</a>.</p>
]]></description>
										<content:encoded><![CDATA[<h2>Overview</h2>
<p>An intelligent power module is a three-phase inverter with its gate drivers, bootstrap diodes and protection comparators already inside. The microcontroller sees six logic inputs, a fault output and three phase terminals, and the design work that remains is the current sensing and the thermal path.</p>
<p>The protection is the part that justifies the cost. Short-circuit detection inside the module reacts in microseconds, faster than firmware polling a shunt could, and it turns the switch off before the device is destroyed. That is a safety function that is hard to build well from discrete parts.</p>
<h2>Key features</h2>
<ul>
<li>Six IGBTs with integrated gate drivers</li>
<li>Bootstrap supply for the high-side drive</li>
<li>Short-circuit and under-voltage protection</li>
<li>Fault output for controller monitoring</li>
<li>1 to 20 kHz switching range</li>
</ul>
<h2>Typical applications</h2>
<ul>
<li>Appliance compressor and fan drives</li>
<li>Small pump and blower inverters</li>
<li>HVAC variable-speed drives</li>
<li>Compact three-phase motor control</li>
</ul>
<h2>Selection note</h2>
<p>The bootstrap capacitors set the high-side drive margin at low switching frequency. Below about 2 kHz, check that the bootstrap supply is refreshed often enough for the gate charge required.</p>
<h2>Ordering</h2>
<p>Send the motor rating, bus voltage, switching frequency and control interface. We confirm the module current class and protection thresholds, then quote.</p>
<p>The post <a href="https://www.duomy.com/products/600v-10a-ipm-three-phase/">600 V 10 A Intelligent Power Module, Three-Phase</a> appeared first on <a href="https://www.duomy.com">DuoMy Sensing</a>.</p>
]]></content:encoded>
					
		
		
			</item>
		<item>
		<title>5 W Isolated DC-DC Converter, 24 V to 5 V, SIP-4</title>
		<link>https://www.duomy.com/products/5w-isolated-dc-dc-24v-5v-sip/</link>
		
		<dc:creator><![CDATA[]]></dc:creator>
		<pubDate>Fri, 20 Nov 2026 01:17:59 +0000</pubDate>
				<guid isPermaLink="false">https://www.duomy.com/products/5w-isolated-dc-dc-24v-5v-sip/</guid>

					<description><![CDATA[<p>Isolated DC-DC converter module, 18 to 36 V input, 5 V 1 A output, 1.5 kV isolation, SIP-4 package. A complete isolated rail without a transformer design.</p>
<p>The post <a href="https://www.duomy.com/products/5w-isolated-dc-dc-24v-5v-sip/">5 W Isolated DC-DC Converter, 24 V to 5 V, SIP-4</a> appeared first on <a href="https://www.duomy.com">DuoMy Sensing</a>.</p>
]]></description>
										<content:encoded><![CDATA[<h2>Overview</h2>
<p>An isolated DC-DC module is a transformer, a controller and a feedback loop in a 20 mm package. It exists because designing an isolated 5 W supply from discrete parts is a week of work and a stack of magnetics samples, while the module is a single line on the bill of materials.</p>
<p>The isolation is what it is bought for: breaking a ground loop between a sensor front end and a controller, or powering a communication interface that must float relative to the main circuit. At 1.5 kV it covers functional isolation, not the reinforced isolation a mains-facing circuit requires.</p>
<h2>Key features</h2>
<ul>
<li>18 to 36 V input, 5 V 1 A output</li>
<li>1.5 kV DC isolation between input and output</li>
<li>SIP-4 package, no external components</li>
<li>78% efficiency at full load</li>
<li>Short-circuit protected output</li>
</ul>
<h2>Typical applications</h2>
<ul>
<li>Isolated sensor and interface supplies</li>
<li>Breaking ground loops in measurement systems</li>
<li>RS-485 and CAN bus isolation</li>
<li>Auxiliary rails in industrial controls</li>
</ul>
<h2>Selection note</h2>
<p>A 5 W module in a sealed enclosure needs derating above 70 °C. Check the derating curve and, if the load is continuous at full current, mount the module where air can reach it.</p>
<h2>Ordering</h2>
<p>Send the input range, output voltage and current, and the isolation class required. We confirm the module against the load profile, then quote.</p>
<p>The post <a href="https://www.duomy.com/products/5w-isolated-dc-dc-24v-5v-sip/">5 W Isolated DC-DC Converter, 24 V to 5 V, SIP-4</a> appeared first on <a href="https://www.duomy.com">DuoMy Sensing</a>.</p>
]]></content:encoded>
					
		
		
			</item>
		<item>
		<title>25 A 1600 V Three-Phase Bridge Rectifier Module</title>
		<link>https://www.duomy.com/products/25a-1600v-three-phase-bridge-module/</link>
		
		<dc:creator><![CDATA[]]></dc:creator>
		<pubDate>Fri, 20 Nov 2026 01:17:58 +0000</pubDate>
				<guid isPermaLink="false">https://www.duomy.com/products/25a-1600v-three-phase-bridge-module/</guid>

					<description><![CDATA[<p>Three-phase bridge rectifier module, 25 A, 1600 V, screw terminals, isolated base. Rectifies a 400 V three-phase supply into a DC bus for drives and large chargers.</p>
<p>The post <a href="https://www.duomy.com/products/25a-1600v-three-phase-bridge-module/">25 A 1600 V Three-Phase Bridge Rectifier Module</a> appeared first on <a href="https://www.duomy.com">DuoMy Sensing</a>.</p>
]]></description>
										<content:encoded><![CDATA[<h2>Overview</h2>
<p>Six diodes in one isolated module turn a three-phase supply into a DC bus with three AC terminals and two DC terminals. The isolated baseplate means the heatsink can be earthed without the terminals being at bus potential, which simplifies the mechanical design of a drive.</p>
<p>At 25 A and 1.5 V per diode, conduction loss is roughly 100 W in a three-phase bridge, so the module is mounted on a heatsink as a matter of course. The 350 A surge rating covers the capacitor charging current at switch-on.</p>
<h2>Key features</h2>
<ul>
<li>Six-diode three-phase bridge in one module</li>
<li>1600 V reverse voltage for 400 V three-phase supplies</li>
<li>Isolated baseplate, 2,500 V AC</li>
<li>M5 screw terminals for field wiring</li>
<li>350 A surge capability</li>
</ul>
<h2>Typical applications</h2>
<ul>
<li>Three-phase input rectification for drives</li>
<li>DC bus generation for inverters</li>
<li>Industrial battery chargers</li>
<li>Uninterruptible supply rectifier stages</li>
</ul>
<h2>Selection note</h2>
<p>Apply thermal compound or a phase-change pad between the baseplate and the heatsink, and tighten the mounting screws to the specified torque in the order given by the drawing.</p>
<h2>Ordering</h2>
<p>Send the input voltage, DC bus current and cooling. We confirm the current class and isolation, then quote.</p>
<p>The post <a href="https://www.duomy.com/products/25a-1600v-three-phase-bridge-module/">25 A 1600 V Three-Phase Bridge Rectifier Module</a> appeared first on <a href="https://www.duomy.com">DuoMy Sensing</a>.</p>
]]></content:encoded>
					
		
		
			</item>
		<item>
		<title>600 V 15 A IGBT Half-Bridge Module</title>
		<link>https://www.duomy.com/products/600v-15a-igbt-half-bridge-module/</link>
		
		<dc:creator><![CDATA[]]></dc:creator>
		<pubDate>Fri, 20 Nov 2026 01:17:58 +0000</pubDate>
				<guid isPermaLink="false">https://www.duomy.com/products/600v-15a-igbt-half-bridge-module/</guid>

					<description><![CDATA[<p>IGBT half-bridge module, 600 V 15 A per switch, with matched freewheeling diodes and isolated baseplate. One part carries the whole commutation loop for a half-bridge stage.</p>
<p>The post <a href="https://www.duomy.com/products/600v-15a-igbt-half-bridge-module/">600 V 15 A IGBT Half-Bridge Module</a> appeared first on <a href="https://www.duomy.com">DuoMy Sensing</a>.</p>
]]></description>
										<content:encoded><![CDATA[<h2>Overview</h2>
<p>A half-bridge module puts both switches and their diodes inside one package, so the commutation loop is defined by the manufacturer instead of by your layout. That is the whole value: the loop inductance that causes turn-off overshoot is fixed and characterised, rather than depending on how the board was routed.</p>
<p>It also removes the isolated mounting problem. The baseplate is isolated from the terminals, so the module bolts to an earthed heatsink and the gate driver only has to bridge the gate-to-emitter isolation, not the full bus voltage.</p>
<h2>Key features</h2>
<ul>
<li>Two IGBTs and two diodes in one package</li>
<li>Characterised commutation loop</li>
<li>Isolated baseplate, 2,500 V AC</li>
<li>Solder-pin power and gate terminals</li>
<li>1.6 °C/W junction-to-case</li>
</ul>
<h2>Typical applications</h2>
<ul>
<li>Half-bridge and full-bridge inverters</li>
<li>Motor drive output stages</li>
<li>Induction heating generators</li>
<li>Welding and plasma supplies</li>
</ul>
<h2>Selection note</h2>
<p>Follow the gate driver layout in the module data sheet. The internal loop is characterised, but the gate loop is still yours, and a long gate return reintroduces the ringing the module was meant to remove.</p>
<h2>Ordering</h2>
<p>Send the bus voltage, switching frequency, current and topology. We confirm the module class and gate driver requirement, then quote.</p>
<p>The post <a href="https://www.duomy.com/products/600v-15a-igbt-half-bridge-module/">600 V 15 A IGBT Half-Bridge Module</a> appeared first on <a href="https://www.duomy.com">DuoMy Sensing</a>.</p>
]]></content:encoded>
					
		
		
			</item>
		<item>
		<title>10 A 1000 V Bridge Rectifier, GBU</title>
		<link>https://www.duomy.com/products/10a-1000v-bridge-rectifier-gbu/</link>
		
		<dc:creator><![CDATA[]]></dc:creator>
		<pubDate>Fri, 20 Nov 2026 01:17:57 +0000</pubDate>
				<guid isPermaLink="false">https://www.duomy.com/products/10a-1000v-bridge-rectifier-gbu/</guid>

					<description><![CDATA[<p>Single-phase bridge rectifier, 10 A, 1000 V, GBU package, 1.05 V forward drop, 200 A surge. Input rectification for supplies in the 100 to 500 W class.</p>
<p>The post <a href="https://www.duomy.com/products/10a-1000v-bridge-rectifier-gbu/">10 A 1000 V Bridge Rectifier, GBU</a> appeared first on <a href="https://www.duomy.com">DuoMy Sensing</a>.</p>
]]></description>
										<content:encoded><![CDATA[<h2>Overview</h2>
<p>The GBU package stands the bridge upright so the body can dissipate into the air instead of into the board, which is what allows 10 A in a footprint that still fits a through-hole layout. It is the standard input rectifier for supplies in the 100 to 500 W range.</p>
<p>At 10 A the bridge dissipates about 21 W, so it needs airflow or a metal chassis nearby. Bonding the flat face to the enclosure with a thermal pad is usually more effective than adding copper to the board.</p>
<h2>Key features</h2>
<ul>
<li>10 A average current at 100 °C case</li>
<li>200 A surge capability</li>
<li>Vertical GBU package for convection cooling</li>
<li>1000 V reverse voltage</li>
<li>2.2 °C/W junction-to-case thermal resistance</li>
</ul>
<h2>Typical applications</h2>
<ul>
<li>Input rectification for 100 to 500 W supplies</li>
<li>Motor drive front ends</li>
<li>Chargers and battery formation equipment</li>
<li>Industrial power modules</li>
</ul>
<h2>Selection note</h2>
<p>Mount the flat face against a metal surface with a thermal pad where possible. The package is designed for that contact, and convection alone limits the current well below the rating.</p>
<h2>Ordering</h2>
<p>Send the output power, input voltage and cooling arrangement. We confirm the current and thermal margin, then quote.</p>
<p>The post <a href="https://www.duomy.com/products/10a-1000v-bridge-rectifier-gbu/">10 A 1000 V Bridge Rectifier, GBU</a> appeared first on <a href="https://www.duomy.com">DuoMy Sensing</a>.</p>
]]></content:encoded>
					
		
		
			</item>
	</channel>
</rss>
