DM-FRD-600V-8A-TO220
Diodes
Rectifiers for power conversion, freewheeling, OR-ing and clamping, from low-voltage Schottky parts to 1,200 V ultrafast recovery devices.
Need a specific part?
Send the part number, quantity and target price. We come back with availability, cross-references and the datasheet.
Request a quote Ask an engineerLead timeQuoted per line
MOQBy line item
Cross-referenceOn request
A diode has three numbers that matter and they pull against each other: forward voltage, reverse recovery time and reverse leakage. Reducing forward voltage usually increases leakage, and increasing voltage rating usually slows recovery. The choice is which of the three the circuit can least afford to lose.
Schottky parts win on forward voltage — 0.3 to 0.5 V against 0.8 to 1.0 V for a silicon PN junction — which is why they dominate low-voltage output rectification. The price is leakage current that rises steeply with temperature: a part with 100 µA at 25 °C can leak tens of milliamps at 125 °C, enough to thermally run away in a poorly cooled design.
Above roughly 200 V, Schottky leakage becomes impractical and the fast-recovery PN diode takes over. Recovery time then becomes the dominant loss term, because every switching cycle the diode must sweep out stored charge while the other switch is turning on. We supply both families across the voltage range where each is the right answer, plus the standard rectifiers that still handle line-frequency work.
Range Overview
Diodes variants
Each variant exists because a different circuit position asks for something different: voltage, current, package and stability trade against each other.
Schottky
0.3-0.5 V VfMetal-semiconductor junction with a low forward drop and effectively zero recovery time. The default for output rectification below 100 V.
Ultrafast recovery
trr < 25 nsPN diode with a short carrier lifetime, trr under 25 ns. Used in switching supplies from 200 V up where Schottky leakage is unacceptable.
Fast recovery
50-200 nstrr in the 50-200 ns band, adequate for lower switching frequencies and for freewheeling in motor drives.
Standard rectifier
Ifsm to 400 ALine-frequency parts for 50/60 Hz bridges and bulk rectification, where recovery time is irrelevant and surge current is the constraint.
SiC Schottky
zero QrrWide-bandgap rectifier with no reverse recovery at all, used in 650 V and 1,200 V designs where Qrr would otherwise dominate.
Catalogue
Diodes — quoted on request
DM-SSD-100V-150M-SOD323
100 V 150 mA Small-Signal Switching Diode, SOD-323
DM-SBD-100V-10A-TO220
100 V 10 A Schottky Rectifier, TO-220
DM-SBD-40V-3A-SMA
40 V 3 A Schottky Barrier Rectifier, SMA
Technical Range
Typical specifications
Figures below are the range across the family, not a single model. Specify the exact range, accuracy and connection on the quote request and we will confirm which variant meets it.
Request a specification check| Parameter | Typical |
|---|---|
| Vrrm | 20 V to 1,200 V |
| If (average) | 1 A to 60 A |
| Vf at rated current | 0.3 V to 1.7 V |
| Reverse recovery trr | 0 ns to 500 ns |
| Reverse leakage | 1 µA to 10 mA |
| Surge current Ifsm | 30 A to 400 A |
| Junction temperature | -55 to +150 °C |
| Packages | SOD-123, SMA/SMB/SMC, DPAK, TO-220, TO-247 |
Applications
Where this family is used
Output rectification in switching supplies
The secondary-side rectifier in flyback, forward and LLC converters, where forward drop sets efficiency at low output voltage.
Freewheeling and clamping
Carries the inductive current when a switch opens, in relay drivers, motor bridges and solenoid control.
OR-ing and reverse-polarity protection
Blocks current from flowing back into a failed supply or a reversed battery, in redundant and battery-backed systems.
Input bridge rectification
Line-frequency bridges where surge current and thermal cycling matter more than recovery speed.
Selection Guide
How to specify correctly
-
1
Decide the voltage class before the current
Below 100 V, Schottky is almost always right. Between 100 and 200 V it depends on leakage and temperature. Above 200 V, fast recovery or SiC is the only practical option.
-
2
Treat leakage as a thermal parameter
Schottky leakage doubles roughly every 10 °C, and the leakage current heats the junction, which increases leakage. At high ambient the loop can run away. Check the leakage at the maximum junction temperature, not at 25 °C.
-
3
Match trr to the switching frequency
Recovery loss is proportional to Qrr × Vr × frequency. At 50 kHz a 200 ns part is acceptable; at 300 kHz the same part can consume more loss than the forward conduction.
-
4
Check Ifsm for inrush and surge
The 8.3 ms surge rating is what survives capacitor charging at power-up. A part sized only on average current can fail on the first switch-on.
-
5
Parallel diodes need thermal symmetry
Forward voltage has a negative temperature coefficient for Schottky parts, so the hotter device takes more current. Parallel parts should share a heatsink and be matched on Vf, or share current through separate resistors.
Used in these industries
All industries →FAQ
Diodes questions
Why does a Schottky diode leak so much when hot?
The metal-semiconductor barrier is lower than a PN junction, which is what gives the low forward drop, but it also lets thermally excited carriers cross in reverse. Leakage roughly doubles every 10 °C, so a part with 50 µA at 25 °C can reach several milliamps at 125 °C. In a design with poor heatsinking, that leakage heats the junction and the current climbs further.
Can I replace a Schottky with an ultrafast recovery diode?
Only where the extra 0.3-0.5 V of forward drop is acceptable. In a 5 V output that is a 6-10% efficiency loss; in a 24 V output it is negligible. The compensation is that the ultrafast part has far lower leakage at high temperature, so it can be the better choice in hot enclosures despite the higher Vf.
How does trr affect efficiency?
During recovery the diode briefly conducts in reverse while the opposite switch is on, so the supply sees a current spike through both devices. The loss per switching event is approximately Qrr × Vr, and multiplied by switching frequency it becomes a continuous loss. Above a few hundred kilohertz it often exceeds the forward conduction loss.
Is it safe to parallel two diodes for more current?
For Schottky parts, not without care: forward voltage falls with temperature, so the hotter device takes more current and gets hotter. Use matched parts from the same lot, mount them on a common heatsink so they track each other, or accept derating. PN junction diodes have a positive Vf temperature coefficient and share current more evenly.
How do I read the Ifsm surge rating?
It is the peak current the junction can survive for a single 8.3 ms half-sine pulse at rated junction temperature, usually at least ten times the average current rating. It matters for inrush into a capacitor bank and for fault transients. Repeated surges accumulate fatigue damage, so a design that sees inrush every power-up should keep the surge well below the rating.
Related categories
Tell us the application and we will confirm the right variant.