DM-FUSE-520-63A-T
Fuses
Overcurrent protection for power entry, battery packs and I/O, in glass, ceramic, SMD and radial PTC formats.
Need a specific part?
Send the part number, quantity and target price. We come back with availability, cross-references and the datasheet.
Request a quote Ask an engineerLead timeQuoted per line
MOQBy line item
Cross-referenceOn request
A fuse is specified by three numbers that are rarely printed together on a distributor page: the current it carries indefinitely, the current it interrupts, and the energy it lets through before it opens. The first is the one everybody reads. The other two decide whether the product fails safely or welds its contacts and starts a fire.
The choice between fast-blow and time-lag is a trade between nuisance blowing and protection speed. A capacitive input draws a large inrush for a few milliseconds; a fast fuse sized to the steady current opens on every power-up. A time-lag fuse rides through the inrush but lets a genuine overload run longer. The correct comparison is the I²t of the inrush against the I²t of the fuse, not the current alone.
We supply cartridge and SMD fuses for board-level and panel protection, resettable PTC devices for ports that get shorted in service, and the automotive blade formats used in vehicle harnesses. Breaking capacity and approvals are quoted per series, because they are not interchangeable between markets.
Range Overview
Fuses & PTCs variants
Each variant exists because a different circuit position asks for something different: voltage, current, package and stability trade against each other.
Ceramic cartridge
to 1,500 AHigh breaking capacity in a sand-filled body, for mains input protection where the prospective short-circuit current is large.
Glass cartridge
visible elementVisible element for equipment where a blown fuse is a diagnostic clue. Lower breaking capacity than ceramic.
SMD thin-film
board levelBoard-level protection for low-voltage rails and USB ports, in 0603 to 2410 sizes with defined I²t.
Resettable PTC
self-resettingPolymeric device that rises in resistance when hot and returns when it cools. For ports that see repeated faults, but it is not a substitute for a fuse at mains voltage.
Automotive blade
blade formatStandard blade formats for vehicle harnesses, with the housing colour encoding the rating.
Catalogue
Fuses & PTCs — quoted on request
DM-PTC-11A-60V
PTC Resettable Fuse, 1.1 A 60 V, Radial
DM-FUSE-0603-500M-FA
0603 Fast-Acting SMD Fuse, 500 mA 32 V
DM-FUSE-1206-2A-SB
1206 Slow-Blow SMD Fuse, 2 A 32 V
Technical Range
Typical specifications
Figures below are the range across the family, not a single model. Specify the exact range, accuracy and connection on the quote request and we will confirm which variant meets it.
Request a specification check| Parameter | Typical |
|---|---|
| Rated current | 0.1 A to 30 A |
| Rated voltage | 32 V to 600 V |
| Breaking capacity | 35 A to 1,500 A |
| Melting I²t | 0.001 to 5,000 A²s |
| Characteristic | Fast-blow (F), time-lag (T) |
| Voltage drop | 30 mV to 300 mV at rated current |
| Approvals | UL, IEC, CCC |
| Packages | 5×20, 6.3×32, 1206, 2410, blade |
Applications
Where this family is used
Mains input protection
The primary fuse in a power supply, where the breaking capacity must exceed what the mains can deliver into a fault.
Battery pack protection
Limits the current a cell can deliver into an external short, in tools, vehicles and backup units.
Port and interface protection
PTC devices on USB, sensor and I/O ports that see repeated short circuits during installation and service.
Motor and transformer circuits
Time-lag fuses that ride through start-up inrush without opening, then protect the winding from a locked rotor.
Selection Guide
How to specify correctly
-
1
Derate the carry current to about 75%
A fuse rated 1 A is intended to carry about 0.75 A indefinitely in a 25 °C environment. Running at the rating, or in a hot enclosure, ages the element and shortens the time to nuisance opening.
-
2
Compare I²t, not current, against inrush
Measure or estimate the inrush waveform, compute its I²t, and choose a fuse whose melting I²t is several times larger. This is the only reliable way to avoid nuisance blowing on capacitive or motor loads.
-
3
Check breaking capacity against the source
A fuse that cannot interrupt the available fault current may arc and continue to conduct, or rupture its body. For mains input, use a ceramic body with a stated high breaking capacity and mount it in a holder rated for the same.
-
4
Do not use a PTC as a mains fuse
Polymeric PTC devices are rated for low voltage and limited fault energy. They are excellent on 5 V and 24 V ports and inappropriate for mains, where a rupturing fault can destroy them without clearing the circuit.
-
5
Account for ambient temperature
Fuse ratings assume 25 °C. In a 60 °C enclosure the carry current falls by 10-20% depending on the series, which is often the difference between a design that works on the bench and one that blows in the field.
Used in these industries
All industries →FAQ
Fuses & PTCs questions
How do I choose between fast-blow and time-lag?
Compare the inrush I²t with the fuse melting I²t. If the load is resistive or the inrush is negligible, fast-blow gives the best protection. If the load is a transformer, motor or a supply with a large input capacitor, the inrush will exceed a fast fuse rating on every start, and a time-lag part is required.
Why does my fuse blow at power-up but not in normal operation?
Inrush. A capacitive input draws a current limited only by the ESR for the first few milliseconds, and its I²t can exceed the fuse melting energy even though the steady current is well within rating. Either move to a time-lag characteristic, increase the rating slightly, or add an inrush limiter.
What does breaking capacity mean?
The maximum fault current the fuse can safely interrupt without rupturing or continuing to arc. If the available short-circuit current exceeds it, the fuse may fail to clear the fault. It is a safety parameter, not a performance one, and it is the reason mains fuses are ceramic rather than glass.
Can a resettable PTC replace a fuse?
On low-voltage signal and port protection, usually yes, and it saves a service call. At mains voltage or where the fault energy is high, no: the PTC has a limited voltage rating and its reset behaviour depends on cooling, which is not guaranteed inside a sealed enclosure.
Do I need to derate a fuse for temperature?
Yes. The rated current assumes 25 °C ambient, and most series lose 10-20% of carry capability at 60 °C. Choose the rating from the derating curve at the actual enclosure temperature, and remember that the fuse holder and the PCB copper also heat the fuse.
Related categories
Tell us the application and we will confirm the right variant.