DM-BTB-08-60P-5H
Board-to-Board Connectors
Mezzanine and parallel-board connectors for stacking logic, sensor and power boards, in fine-pitch SMT and through-hole variants.
Need a specific part?
Send the part number, quantity and target price. We come back with availability, cross-references and the datasheet.
Request a quote Ask an engineerLead timeQuoted per line
MOQBy line item
Cross-referenceOn request
A board-to-board connector is specified by three numbers before anything else: pitch, stack height and current per contact. Pitch sets how many signals fit, stack height sets the mechanical gap between the boards, and current per contact sets how many pins must be dedicated to power and ground. Getting the order wrong means a connector that fits mechanically but cannot carry the current, or one that carries the current but will not close to the height the enclosure allows.
The second issue is tolerance. Two boards that are parallel in CAD are never parallel in production, and a rigid connector absorbs that mismatch as stress on the solder joints. Above roughly 40 mm of board length, or wherever a board is screwed down at both ends, a floating or compliance connector is worth the extra cost.
We supply fine-pitch mezzanine parts for dense logic stacks, 2.54 mm headers for industrial boards and prototypes, and floating variants where the mechanical stack cannot be controlled tightly. Plating thickness and mating cycle ratings are the two specifications most often ignored and most often responsible for field failures.
Range Overview
Board-to-Board Connectors variants
Each variant exists because a different circuit position asks for something different: voltage, current, package and stability trade against each other.
Fine pitch 0.4-0.5 mm
high densityHigh-density mezzanine connectors for processor modules and camera boards, with stack heights from 1.5 mm and contact counts above 100.
1.0-1.27 mm pitch
general purposeThe general-purpose middle ground: enough density for most logic stacks, with better routing room and more robust contacts than 0.4 mm.
2.54 mm header and socket
3 A per pinThrough-hole or SMT pin headers with matching sockets, used on industrial boards and prototypes where density is secondary.
Floating / compliance
tolerance absorbingSpring-loaded contacts that absorb XY and angular misalignment between boards, protecting solder joints in screwed assemblies.
Board-to-FPC (ZIF)
flex cableZero-insertion-force connectors for flex cable, used where the two boards connect through a flexible section rather than directly.
Catalogue
Board-to-Board Connectors — quoted on request
DM-HDR-127-2X20
1.27 mm Pitch 2×20 Pin Header, Through-Hole
DM-HDR-254-1X40-F
2.54 mm Pitch 1×40 Female Header, Through-Hole
DM-BTB-05-20P-4H
0.5 mm Pitch 20-Pin Board-to-Board Connector, 4 mm Stack
Technical Range
Typical specifications
Figures below are the range across the family, not a single model. Specify the exact range, accuracy and connection on the quote request and we will confirm which variant meets it.
Request a specification check| Parameter | Typical |
|---|---|
| Pitch | 0.4 / 0.5 / 0.8 / 1.0 / 1.27 / 2.0 / 2.54 mm |
| Contact count | 10 to 240 positions |
| Current per contact | 0.3 A to 3 A |
| Stack height | 1.5 mm to 20 mm |
| Mating cycles | 20 to 500 |
| Plating | Gold flash to 0.76 µm over nickel |
| Operating temperature | -55 to +125 °C |
| Mounting | SMT, through-hole, hybrid with locating pegs |
Applications
Where this family is used
Processor and FPGA mezzanine
Carries high-speed differential pairs between a compute module and a carrier board, where pitch and impedance both matter.
Display and camera modules
Fine-pitch connectors with controlled stack height, often combined with a shield can for EMI.
Sensor and I/O expansion boards
Modular stacks where a base board accepts one of several daughter cards, so mating cycles and keying become important.
Industrial backplanes
2.0 and 2.54 mm connectors carrying power and slow signals between cards in a chassis, with high current per pin.
Selection Guide
How to specify correctly
-
1
Fix the stack height from the enclosure, not the catalogue
Stack height is set by the series and cannot be adjusted. Measure the mechanical gap including tolerance stack-up, PCB thickness variation and any gasket, then choose the series that fits with margin.
-
2
Allocate power and ground pins deliberately
Current per contact falls when adjacent contacts are loaded, because heat has nowhere to go. A 0.5 mm pitch connector rated 0.5 A per contact may only be good for 0.3 A when every pin is carrying current.
-
3
Use floating connectors where the boards are screwed down
A rigid connector between two boards fixed at both ends puts the tolerance into the solder joints. Floating contacts absorb it, at a small cost in height and price.
-
4
Match plating thickness to mating cycles
Gold flash is adequate for a connector mated once in the factory. Anything that gets unplugged during service needs 0.4 µm or more, and a corrosive atmosphere pushes that higher again.
-
5
Check coplanarity for fine-pitch SMT
At 0.4 mm pitch, a contact that sits 0.1 mm high will not reflow reliably. Confirm the connector is shipped in tape with a coplanarity specification, and use the recommended land pattern rather than a scaled one.
Used in these industries
All industries →FAQ
Board-to-Board Connectors questions
Is 0.4 mm pitch practical for normal assembly?
Yes, with the right process: laser-cut stencil, solder paste inspection, and AOI after reflow. It is not a hand-soldering proposition, and rework needs hot air with a preheat stage. If the assembly house does not already run 0.4 mm parts, 0.5 mm costs less in yield than it saves in board area.
Is gold flash enough for the contact plating?
For a connector mated once and never touched again, yes. Flash is typically 0.05-0.1 µm over nickel and protects the contact during storage. For anything with more than about 20 mating cycles, or in a sulphur-bearing atmosphere, specify 0.4 µm or more, because thin gold wears through and exposes the nickel underneath.
When do I need a floating connector?
When two boards are mechanically constrained at more than one point — screwed at both ends, or held in a chassis — and the connector cannot absorb the resulting misalignment. A rigid connector in that position loads the solder joints, and the failure appears as a cracked fillet after thermal cycling rather than at first assembly.
How is the mating cycle rating determined?
The manufacturer cycles the connector to its rated count and measures contact resistance. The rating is the point where resistance has risen by a defined amount, typically 20 mΩ. It assumes clean mating, so a connector used in a dusty environment reaches that limit earlier than the number suggests.
How do I control coplanarity on fine-pitch parts?
Buy in tape and reel with a stated coplanarity spec, use the manufacturer land pattern without modification, keep the stencil aperture area ratio above 0.66, and support the connector body during reflow so it does not tilt. Measure a sample after reflow with a shadow moiré or laser system if the assembly is safety-related.
Related categories
Tell us the application and we will confirm the right variant.