DM-USBC-PLUG-24P
USB & Type-C Connectors
Type-C and legacy USB receptacles for charging, data and combined duty, including vertical, mid-mount and IPX7 waterproof variants.
Need a specific part?
Send the part number, quantity and target price. We come back with availability, cross-references and the datasheet.
Request a quote Ask an engineerLead timeQuoted per line
MOQBy line item
Cross-referenceOn request
USB Type-C is not one connector. A 16-pin receptacle carries USB 2.0 data and up to 3 A of power; a 24-pin receptacle adds the SuperSpeed pairs needed for 5 Gbps and above. They look identical from outside and are not interchangeable, which is why so many products ship with a port that charges but will not transfer data at the advertised speed.
The second misconception is that the connector sets the power. It does not. A Type-C port delivers 5 V until the CC pins negotiate something else, and higher voltage or current requires a PD controller on both ends. The receptacle only has to survive the current: 3 A contacts for standard cables, 5 A contacts if the design intends to use an electronically marked cable at 100 W.
We supply the receptacles that cover charging-only, data-plus-charging and full-featured designs, in horizontal, vertical and mid-mount terminations, including waterproof versions for equipment that gets washed or rained on. The choice between 16 and 24 pins is the first decision, and it is decided by whether the product needs SuperSpeed at all.
Range Overview
USB & Type-C Connectors variants
Each variant exists because a different circuit position asks for something different: voltage, current, package and stability trade against each other.
Type-C 16-pin
USB 2.0 + powerUSB 2.0 data plus charging, with the CC pins for orientation and power negotiation. The lower-cost option where SuperSpeed is not needed.
Type-C 24-pin full featured
up to 40 GbpsAdds TX/RX SuperSpeed pairs for 5-40 Gbps depending on the controller, plus SBU pins for alternate modes such as DisplayPort.
Waterproof Type-C
IPX7 / IPX8Sealed receptacle rated IPX7 or IPX8, with an O-ring or gasket interface to the enclosure, for outdoor and washdown equipment.
Mid-mount and vertical
space savingTerminations that let the connector sit flush with the PCB edge or stand upright, for slim enclosures and right-angle cable entry.
USB-A, micro-B, USB-B
legacyLegacy receptacles still required on industrial equipment, chargers and host ports where the cable population is USB-A.
Catalogue
USB & Type-C Connectors — quoted on request
DM-USBC-24P-G2-MID
USB 3.2 Gen 2 Type-C Receptacle, 24-Pin, Mid-Mount
DM-USBC-16P-IPX7
Waterproof USB Type-C Receptacle, IPX7, 16-Pin
DM-USBC-16P-SMT
USB 2.0 Type-C Receptacle, 16-Pin, SMT
Technical Range
Typical specifications
Figures below are the range across the family, not a single model. Specify the exact range, accuracy and connection on the quote request and we will confirm which variant meets it.
Request a specification check| Parameter | Typical |
|---|---|
| Positions | 16 (USB 2.0) / 24 (full featured) |
| Rated current | 3 A standard, 5 A high-power |
| Rated voltage | 20 V (USB PD), 48 V (EPR) |
| Data rate | 480 Mbps to 40 Gbps |
| Mating cycles | 10,000 |
| Insertion force | 5-20 N |
| Mounting | SMT, through-hole shell, hybrid with locating pegs |
| Waterproof rating | IPX7 / IPX8 on sealed variants |
Applications
Where this family is used
Charging ports on portable equipment
A 16-pin receptacle with CC resistors for basic 5 V charging, or with a PD controller for fast charging.
Data and power on instruments
A 24-pin receptacle carrying both the configuration interface and the supply, avoiding a second connector.
Outdoor and washdown devices
Sealed receptacles with a gasket interface, used on handheld terminals, medical carts and agricultural equipment.
Industrial panel and DIN-rail units
Vertical and mid-mount parts where the cable enters through the front panel and the PCB sits parallel to it.
Selection Guide
How to specify correctly
-
1
Decide 16-pin or 24-pin from the data requirement
If the product only needs USB 2.0 and charging, 16 pins is cheaper and easier to route. If it needs SuperSpeed or an alternate mode, 24 pins is mandatory and the differential pairs need impedance control.
-
2
Set the CC resistors to match the intended role
A sink pulls 5.1 kΩ on each CC pin for basic 5 V. Anything above that requires a PD controller that negotiates. Getting this wrong produces a port that charges from some cables and not others.
-
3
Use 5 A contacts only with a 5 A design
The 5 A rating only delivers if the cable is electronically marked, the controller negotiates, and the PCB traces and ground plane can carry the current. A 5 A receptacle on a 3 A layout adds cost without adding capability.
-
4
Plan the shell anchors before the signal pads
Insertion and extraction force goes through the shell, not the signal contacts. Through-hole or hybrid shell anchors with locating pegs spread the load; a pure SMT shell can lift under repeated cable stress.
-
5
Match the waterproof rating to the enclosure
An IPX7 receptacle only achieves IPX7 with the corresponding gasket and a flat, correctly finished enclosure surface. The connector alone is not a seal.
Used in these industries
All industries →FAQ
USB & Type-C Connectors questions
What is the difference between 16-pin and 24-pin Type-C?
The 24-pin version adds the four SuperSpeed differential pairs and the two sideband-use pins. A 16-pin part carries USB 2.0, power, ground and CC only. Externally identical, so a 16-pin receptacle on a board advertised as USB 3.2 will charge and run USB 2.0 but never reach the higher data rate.
Why does my Type-C port charge but not transfer data?
Most often a 16-pin receptacle on a design that expects SuperSpeed, or D+/D- not routed to the controller. The second most common cause is a CC configuration that makes the port present as a charging-only source. Check the pin count on the BOM first.
How are the CC pins wired?
For a device that only sinks power, 5.1 kΩ from each CC pin to ground, independently. For anything that negotiates higher voltage or current, a PD controller drives the CC pins and the resistors are not fitted. Never tie the two CC pins together; the orientation detection depends on them being separate.
What is needed for 5 A / 100 W charging?
A receptacle with 5 A rated power contacts, an electronically marked cable that declares its current capability, a PD controller that negotiates the contract, and PCB copper sized for 5 A with margin. Missing any one of the four limits the port to 3 A or less.
How does a connector achieve IPX7?
The receptacle has a moulded body and an O-ring or gasket face that compresses against the enclosure when the connector is screwed or clipped in. The seal is a system: the enclosure surface must be flat and clean, the screws must be torqued evenly, and the cable side needs its own sealing if the plug is not waterproof.
Related categories
Tell us the application and we will confirm the right variant.