Passive Components

MLCC Capacitors

Multilayer ceramic capacitors from 0.5 pF to 100 µF, in case sizes from 0402 to 2220, with Class 1 and Class 2 dielectrics and automotive-grade termination options.

5 variants 5 catalogue items ±30 ppm/°C -55 to +125 °C high CV

Need a specific part?

Send the part number, quantity and target price. We come back with availability, cross-references and the datasheet.

Request a quote Ask an engineer

Lead timeQuoted per line

MOQBy line item

Cross-referenceOn request

An MLCC is the cheapest part on the board and the one most likely to be wrong. The failure mode is rarely a short; it is a capacitor that measures a quarter of its nominal value under DC bias, or one whose Class 2 dielectric drifts 15% across the operating temperature while the design assumed it would not. Both faults pass incoming inspection and both show up months later as noise, instability or a reset that nobody can reproduce.

The choice that matters is dielectric class, not capacitance. Class 1 (C0G / NP0) is a linear dielectric with no voltage coefficient and no piezoelectric behaviour, which makes it the only option for oscillators, RF matching and precision filters. Class 2 (X7R, X5R, X6S, Y5V) packs ten to a hundred times more capacitance into the same case, at the cost of a capacitance that falls with applied voltage and a tolerance that widens with temperature.

Procurement is where the two classes get confused. A 100 nF 0402 exists in dozens of part numbers that differ only in voltage rating, dielectric, termination and qualification, and they are not interchangeable in a circuit even when the first page of the datasheet looks identical. We cross-reference by dielectric, voltage and case size first, then confirm the DC bias curve for the rail the part will actually sit on.

Range Overview

MLCC Capacitors variants

Each variant exists because a different circuit position asks for something different: voltage, current, package and stability trade against each other.

C0G / NP0 (Class 1)

±30 ppm/°C

Ultra-stable dielectric with no voltage coefficient and negligible ageing. Used where capacitance defines a frequency or a filter response.

X7R (Class 2)

-55 to +125 °C

The general-purpose workhorse: -55 to +125 °C with ±15% capacitance change, and the widest availability in mid-range values.

X5R (Class 2)

high CV

Higher volumetric capacitance than X7R but rated only to +85 °C. Common on consumer rails where the thermal margin is generous.

Soft-termination MLCC

AEC-Q200

A conductive polymer layer between ceramic body and terminal absorbs board flex, preventing the flex cracks that open after depanelisation and screw fixing.

High-voltage series

1-3 kV

1 kV to 3 kV ratings in 1206 and larger cases for snubbers, EMI filters and X-capacitor positions in offline supplies.

Catalogue

MLCC Capacitors — quoted on request

Browse all products

Technical Range

Typical specifications

Figures below are the range across the family, not a single model. Specify the exact range, accuracy and connection on the quote request and we will confirm which variant meets it.

Request a specification check
Parameter Typical
Capacitance range 0.5 pF to 100 µF
Case sizes 0402 / 0603 / 0805 / 1206 / 1210 / 1812 / 2220
Rated voltage 6.3 V to 3 kV DC
Dielectrics C0G, X7R, X5R, X6S, Y5V
Tolerance ±0.1 pF to ±20%
Operating temperature -55 to +125 °C
Termination Ni/Sn, soft termination, AgPd
Packaging 7-inch and 13-inch reels, 1k to 10k per reel
Qualification AEC-Q200, automotive grade

Applications

Where this family is used

Decoupling and bulk bypass

Placed close to the load to supply transient current and shunt switching noise back to the return plane. The value is chosen by impedance at the switching frequency, not by capacitance alone.

EMI filtering on interfaces

Feed-through and X/Y positions in input filters, where the capacitor works with a choke to keep conducted emissions inside the limit line.

Snubbers and resonant tanks

High-voltage C0G parts in flyback and LLC primaries, where a capacitance that shifts with temperature would detune the resonant point.

Timing and RF matching

Oscillator load capacitors, PLL loop filters and antenna matching networks, all of which need a dielectric that does not move with voltage or temperature.

Selection Guide

How to specify correctly

  1. 1

    Read the DC bias curve before the nominal value

    A 10 µF X5R 0603 6.3 V can lose 60-70% of its capacitance at rated voltage. If the rail sits at 5 V, the effective value is closer to 3-4 µF, and any filter designed on 10 µF will be mistuned.

  2. 2

    Match the dielectric to the temperature window

    X5R stops at +85 °C. Above that the capacitance falls off a cliff, which is why an X5R chosen for a 70 °C enclosure becomes a different part in a 95 °C one.

  3. 3

    Derate Class 2 voltage to about half

    Running an X7R at 100% of rated voltage accelerates both ageing and the DC bias loss. Half rating is the usual industrial margin, with 80% acceptable in benign conditions.

  4. 4

    Check flex-crack risk on large boards

    Cases of 1206 and above on a board that is depanelised or screwed down at the corners should use soft termination. The crack does not appear at test; it appears after thermal cycling.

  5. 5

    Verify case size against the land pattern

    An 0805 land pattern accepts an 0603 part with poor solder fillets. Confirm both the body size and the termination width before releasing the BOM.

FAQ

MLCC Capacitors questions

Why does my 10 µF X5R capacitor measure 3 µF in circuit?

DC bias. Class 2 ceramics lose capacitance as the applied voltage approaches the rating, because the barium titanate domains align with the field. A 10 µF 6.3 V part on a 5 V rail commonly reads 30-50% of nominal. Measure with a meter that applies bias, or read the manufacturer bias curve at your actual rail voltage.

Can I substitute X5R for X7R?

Only if the board never exceeds +85 °C and the capacitance tolerance across temperature is not part of the design margin. X5R is specified to +85 °C with ±15%; above that the change is unbounded. For anything with an enclosure temperature above 70 °C, keep X7R.

What is soft termination and when is it needed?

A flexible conductive layer between the ceramic body and the nickel barrier. It absorbs the bending stress that otherwise starts a crack at the termination. Use it on cases 1206 and larger, on boards thinner than 1.0 mm, and anywhere the assembly is depanelised by hand or fixed with screws near the capacitor.

Are two 100 nF capacitors in parallel better than one 220 nF?

Usually yes for decoupling. Two packages halve the equivalent ESL and give a lower impedance over a wider band, which is what actually suppresses switching transients. The 220 nF is only better where board area is the binding constraint.

How do I cross-reference an MLCC part number?

Decode four fields in order: case size, dielectric, voltage rating and capacitance tolerance. Only then compare the DC bias curve, the termination type and the qualification. Two parts that match on the first four can still differ on bias behaviour by a factor of two. Send the original part number and the rail voltage and we will return the equivalent with the bias curve attached.