Power Inductors & TLVR
Molded and assembled power inductors for DC-DC conversion, including trans-inductor (TLVR) parts for multiphase regulators that need faster transient response.
Need a specific part?
Send the part number, quantity and target price. We come back with availability, cross-references and the datasheet.
Request a quote Ask an engineerLead timeQuoted per line
MOQBy line item
Cross-referenceOn request
Three numbers decide whether a power inductor works: inductance, saturation current and RMS current. They trade against each other inside a fixed footprint, and the datasheet presents all three at conditions that rarely match the application. The most common failure is selecting on saturation current measured at a 30% roll-off when the design needs 20%, which puts the converter into current limit on the first load step.
The second decision is topology. A conventional multiphase buck puts one inductor per phase and relies on the controller to interleave them. A trans-inductor voltage regulator (TLVR) couples the phases through a secondary winding, so a load step on one phase is reflected into all of them almost instantly. The result is a large reduction in output capacitance for the same transient, which is why TLVR has become standard on high-current processor rails.
We supply molded shielded inductors for general DC-DC work and TLVR coupled inductors for multiphase rails. The part selection is driven by the ripple target, the peak current and the thermal path, and we will model the ripple at your actual input and output voltages rather than quoting the catalogue test condition.
Range Overview
Power Inductors & TLVR variants
Each variant exists because a different circuit position asks for something different: voltage, current, package and stability trade against each other.
Molded metal-composite
up to 100 APressed iron powder body with a self-shielded structure: high saturation current, low DCR, soft saturation that degrades gracefully under overload.
Assembled shielded
cost-optimisedFerrite core with a shielding can, lower cost than molded parts, with a sharper saturation knee that must be respected.
TLVR coupled inductor
multiphase VRMTwo windings on one core: the primary carries the phase current, the secondary is series-connected across phases to speed the transient response.
Unshielded / rod core
EMI cautionLowest cost, highest stray field. Acceptable only where the inductor is far from sensitive traces and the enclosure contains the flux.
Thin-film / multilayer
high frequencySmall inductance values at high frequency for RF and low-current point-of-load stages where a wirewound part is physically too large.
Catalogue
Power Inductors & TLVR — quoted on request
DM-IND-1R5-20A-1010
1.5 µH 20 A Low-Profile Power Inductor, 10 × 10 mm
DM-IND-100-6A-0808
10 µH 6 A Shielded Power Inductor, 8 × 8 mm
DM-IND-4R7-10A-1212
4.7 µH 10 A Shielded Power Inductor, 12 × 12 mm
Technical Range
Typical specifications
Figures below are the range across the family, not a single model. Specify the exact range, accuracy and connection on the quote request and we will confirm which variant meets it.
Request a specification check| Parameter | Typical |
|---|---|
| Inductance | 0.1 µH to 1 mH |
| Saturation current (Isat) | 1 A to 100 A |
| RMS current (Irms) | 0.5 A to 60 A |
| DC resistance | 1 mΩ to 500 mΩ |
| Self-resonant frequency | 5 MHz to 200 MHz |
| Footprint | 4×4×2 mm to 17×17×7 mm |
| Shielding | Molded, shielded can, unshielded |
| Temperature range | -40 to +125 °C |
Applications
Where this family is used
Buck converter output stage
The main energy storage element in every point-of-load regulator, sized by the ripple target and the load-step requirement.
Multiphase processor VRM
Six to sixteen phases feeding a CPU or GPU rail, where TLVR coupling cuts the output capacitance needed for a given transient.
LED drivers and chargers
Continuous-conduction stages where the inductor sets the current ripple and therefore the output capacitor stress.
Input filters on DC-DC modules
Blocks switching noise from propagating back onto the input bus, working with a capacitor to form a two-pole filter.
Selection Guide
How to specify correctly
-
1
Use the saturation curve at the real peak current
Peak current is DC output plus half the ripple. Read the inductance at that peak from the curve, not the nominal value, and confirm the roll-off percentage you actually need. A part quoted at 30% may be at 50% in your circuit.
-
2
Target 20-40% ripple current
Below 20% the inductance is larger than necessary and the transient response suffers. Above 40% the core loss and the output capacitor ripple both climb. The optimum depends on the switching frequency and the load-step spec.
-
3
Account for DCR heating in a sealed enclosure
The Irms rating assumes a 40 °C rise in open air. Inside a sealed box the local ambient may already be 60 °C, which consumes most of the thermal margin before the part carries any current.
-
4
Check self-resonant frequency against the harmonics
Above SRF the part behaves capacitively. If the switching edge has significant energy at the third or fifth harmonic and SRF is close to it, the filter stops working exactly where it is needed.
-
5
TLVR needs matched phases and controller support
TLVR only delivers its transient advantage with a controller that supports the topology and with matched primary inductance across phases. It is not a drop-in replacement for the inductors on an existing board.
Used in these industries
All industries →FAQ
Power Inductors & TLVR questions
What is the difference between Isat and Irms?
Isat is the current at which inductance has fallen by a stated percentage, usually 20-30%, because the core is saturating. Irms is the current that produces a specified temperature rise, usually 40 °C, limited by winding and core loss. A part must satisfy both: exceed Isat and the converter loses regulation; exceed Irms and the part overheats over time.
When should I use TLVR instead of a conventional multiphase design?
When the load steps are large and fast enough that the output capacitor bank becomes the dominant cost or the dominant board area. TLVR reflects a step across phases within a few nanoseconds, which cuts the capacitance needed. It also requires a compatible controller and matched phases, so it is a topology decision, not a component swap.
Why does inductance drop as DC current rises?
The core material approaches saturation, so its permeability falls and the inductance falls with it. Molded metal-composite parts have a soft knee that degrades gradually; ferrite parts have a sharper knee and can lose most of their inductance within a small current band. This is why the roll-off percentage matters more than the headline Isat number.
Can I use a larger inductance to reduce output ripple?
Yes, but at a cost in transient response and size. Doubling the inductance halves the ripple, which reduces output capacitor ripple current, but it also slows the current slew during a load step, so the output capacitor has to supply the load for longer. In multiphase designs the ripple is already low, and the constraint is usually the transient rather than the ripple.
How do I choose between molded and assembled cores?
Molded metal-composite parts win on saturation behaviour, shielding and mechanical robustness, and they are the default above a few amps. Assembled ferrite parts are cheaper and adequate for lower currents where the saturation knee has margin. If the enclosure is tight or the current is pulsed, molded is the safer choice.
Related categories
Tell us the application and we will confirm the right variant.