DM-AEC-102M-35-SN18
Aluminium Electrolytic Capacitors
Bulk storage and ripple filtering from 0.1 µF to 100,000 µF, in radial, SMD and snap-in packages rated to +105 °C or +125 °C.
Need a specific part?
Send the part number, quantity and target price. We come back with availability, cross-references and the datasheet.
Request a quote Ask an engineerLead timeQuoted per line
MOQBy line item
Cross-referenceOn request
An electrolytic capacitor is the only common component whose lifetime is specified rather than assumed. The datasheet life figure — typically 2,000 to 12,000 hours — is quoted at rated voltage and maximum category temperature, and every ten degrees below that roughly doubles the expected life. A supply that runs its electrolytics at 105 °C will need them replaced; the same supply running at 75 °C will outlast the equipment.
The practical selection problem is that life, ripple current and ESR are coupled. A low-ESR part handles more ripple without self-heating, which extends life, but low-ESR parts are physically larger and cost more. A high-capacitance part in the same can has thinner foil and a lower ripple rating. You cannot maximise all three in one package, so the design has to state which one the application actually needs.
We supply the three package families that cover most industrial boards: radial leaded for through-hole assembly, SMD V-chip for automated lines, and snap-in or screw terminal for the bulk position on power supplies and motor drives. Polymer hybrid parts are available where the ripple current or the low-temperature ESR would otherwise force a much larger can.
Range Overview
Aluminium Electrolytic Capacitors variants
Each variant exists because a different circuit position asks for something different: voltage, current, package and stability trade against each other.
Radial leaded
2,000-10,000 hThrough-hole cans from 4 mm to 18 mm diameter, the default for industrial control boards and prototypes where hand assembly is acceptable.
SMD V-chip
automated assemblySurface-mount base plate for reflow assembly, with low profile for boards that sit under a lid or inside a DIN enclosure.
Snap-in / screw terminal
up to 6 A rippleLarge can devices for DC-link and input bulk positions, with ripple current ratings in the multi-amp range.
Polymer hybrid
low ESRConductive polymer plus liquid electrolyte: low ESR at low temperature, higher ripple capability and no dry-out failure mode at end of life.
Long-life series
10,000 h+105 °C parts rated 10,000-12,000 hours, used where the capacitor is not serviceable after installation.
Catalogue
Aluminium Electrolytic Capacitors — quoted on request
DM-AEC-101M-35-0810
100 µF 35 V SMD Aluminium Electrolytic, V-Chip
DM-AEC-010M-50-0511
10 µF 50 V Radial Aluminium Electrolytic, 105 °C
DM-AEC-221M-25-0812
220 µF 25 V Low-ESR Radial Electrolytic, 105 °C
Technical Range
Typical specifications
Figures below are the range across the family, not a single model. Specify the exact range, accuracy and connection on the quote request and we will confirm which variant meets it.
Request a specification check| Parameter | Typical |
|---|---|
| Capacitance | 0.1 µF to 100,000 µF |
| Voltage | 6.3 V to 500 V DC |
| Endurance | 2,000 h to 12,000 h at 105 °C |
| Ripple current | 30 mA to 6 A at 100 kHz / 105 °C |
| ESR | 20 mΩ to 5 Ω |
| Capacitance tolerance | ±20% (M) |
| Temperature range | -40 to +105 °C |
| Case sizes | 4×5 mm to 35×50 mm |
Applications
Where this family is used
Input bulk and hold-up
Stores energy across the rectified mains cycle so the downstream converter sees a stable DC bus, and provides ride-through for short dips.
Output ripple filtering
Absorbs the switching ripple that the inductor cannot remove, in LED drivers, chargers and DC-DC modules.
Motor drive DC link
Snap-in and screw terminal banks handle the pulsed current of inverter bridges and absorb regenerative energy.
Audio and instrumentation smoothing
Large capacitance with moderate ESR, where the requirement is a low-frequency pole rather than high-frequency impedance.
Selection Guide
How to specify correctly
-
1
Size ripple current at the actual switching frequency
The catalogue figure is quoted at 100 kHz. At 50 Hz or 120 Hz the allowable ripple drops sharply, and the correction factor table on the datasheet is not optional. Use the frequency of the current the part will really see.
-
2
Calculate life at the real ambient temperature
Life = rated life × 2^((Tmax - Ta)/10) × voltage factor. A 105 °C 5,000 h part at 65 °C gives roughly 80,000 hours; the same part at 95 °C gives 10,000. Design to the enclosure temperature measured with the lid on.
-
3
Check ESR at the cold start condition
Electrolyte viscosity rises as temperature falls, and ESR can multiply by ten at -40 °C. Equipment that must start cold needs either a polymer hybrid part or a soft-start that limits the initial ripple.
-
4
Leave vent clearance and observe polarity
The vent is a pressure relief, not decoration. Keep it clear of the enclosure wall, and make sure the silkscreen polarity mark survives assembly, because a reversed electrolytic fails short and vents.
-
5
Watch the sleeve on long-life series
Counterfeit and re-sleeved capacitors are common in long-life series, where the outer sleeve carries the rating. Buy through traceable distribution and check the date code against the shipment.
Used in these industries
All industries →FAQ
Aluminium Electrolytic Capacitors questions
How is electrolytic capacitor life calculated?
The standard formula is L = L0 × 2^((Tmax - Ta)/10) × K, where L0 is the rated endurance, Tmax the category temperature, Ta the ambient at the capacitor and K a voltage derating factor between 0.7 and 1.0. It is an estimate of the time for capacitance to drop 20% or ESR to double, not a guarantee, so most designs apply a further safety factor of two.
Can I replace a 105 °C part with an 85 °C part?
Only if the ambient at the capacitor is comfortably below 85 °C and the ripple current de-rating works out. In practice a 105 °C part in a 70 °C enclosure has four times the life of an 85 °C part in the same place, so the 85 °C substitution usually shortens service life. It is rarely the saving it looks like.
What causes the top of a capacitor to bulge?
Gas generation from electrolyte breakdown, driven by overvoltage, reverse polarity, excessive ripple heating or a dried-out electrolyte after end of life. Bulging is a late symptom: by the time the vent lifts, capacitance has usually fallen well below tolerance. Replace the whole bank, not just the failed can.
When should I use polymer hybrid instead of liquid electrolytic?
When the ripple current is high relative to the can size, when the equipment must start at -40 °C, or when a dry-out failure mode is unacceptable. Polymer hybrid parts have lower ESR and a safer end of life, but they cost more and are limited in the highest voltage ratings.
Why does the capacitance drop at low temperature?
The electrolyte conductivity falls as temperature falls, which raises ESR and reduces the effective capacitance at the measurement frequency. A part measured at 100 Hz and -40 °C can read 20-30% low. It is not a defect; it is a property of the chemistry, and it is why cold-start ripple must be checked separately.
Related categories
Tell us the application and we will confirm the right variant.